Floor Panel- Superimposed floor panel,Floor board ,Superimposed floor slabs
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 5000 m²
- Supply Capability:
- 20000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
1、The use of large column nets can reduce the cost of building pile foundations on rock book soft soil foundations.
2、The full height of the superimposed floor panel is smaller than the full height of the hollow floorpanel, which can reduce the overall height of the high-rise building or increase its number of floors.
3、Saving concrete shuttering.
4、The bottom surface of the plate is flat, and the ceiling of the building does not have to be plastered, reducing indoor wet work and accelerating the construction progress.
5、The individual components are lightweight, flexible, easy to transport and install, and can use existing construction machinery and equipment.
- Q: What is the quality of the snowboard?
- Chevrolet board than the ordinary lunch box bubble to more than five times, relatively hard, the quality of the general, generally used in the more low-end place. Specifically you ask what the quality is not clear, you know these
- Q: What kind of plates are used for building models? In addition to the abs board kt board
- With snowflakes
- Q: What kind of PCB need to use Anti-CAF sheet
- Anti-CAF is a material with special characteristics! In fact, the ordinary FR4 sheet also has enough of this feature, but in the special areas of the product may require more stringent reliability, so the material supplier was the introduction of such a special plate! Electronic migration is mainly a greater impact on the environment, such as humid environment will exacerbate the risk of electronic migration! From the product structure, such as the spacing between the holes is too small, will also cause greater risk!
- Q: Cabinet cabinet board types which
- Stainless steel cabinets Now the market is relatively stylish cabinet is a stainless steel cabinet, its advantage is strong, resistant to operation, easy to clean, favored by young consumers, but it has a disadvantage is the summer heat performance is not good. The king and feel, in fact, how many people care about the summer heat effect, we are more concerned about the bear child throwing something in the above hit a pit
- Q: Snow Ling plate quality how, I now want to decorate, intended to use snow plate
- With snow Ling plate, rest assured, of course, must go to the store to choose genuine Oh, secretly tell you one, now a lot of counterfeit.
- Q: How is the environmental standard of the plate defined?
- According to China's environmental standards, according to the concept of formaldehyde emission limit, the limit of formaldehyde in the plate is divided into three levels, namely E2 ≤ 5.0mg / L, E1 ≤ 1.5mg / L, E0 ≤ 0.5mg / L The Plate to meet the E2 level standard, that is, E2, E1 and E0 class plate can be called the green sheet, but because of consumer awareness of environmental protection, and now the market more common E1 or even E0 grade plate. ???? E0 standard is to allow formaldehyde in the plate, but can not exceed 0.5mg / L, which is the highest upper limit; the lower limit should be the highest content of wood aldehyde itself (wood self-aldehyde content is generally 0.12mg / L-0.04mg / L) That is the lower limit is 0.12mg / L. ??? "Zero formaldehyde" is the choice of non-formaldehyde, the production process does not produce aldehyde; on the environment of the production staff do not bring any pollution and injury. From this we can give "zero formaldehyde" plate so that the free aldehyde in the plate is less than or equal to the content of the wood itself (usually 0.04mg / L-0.12mg / L). "Zero formaldehyde" sheet and E0 is not the same thing, "zero formaldehyde" sheet principle that higher than the E0 level.
- Q: Will the sheet metal processing bending coefficient and plate thickness, bending angle, bending radius is what is the relationship between the urgent!
- The bending factor and the thickness of the material you said bending angle ah bend the radius and bending the bending machine up and down mold, the length of the bending parts are related We are using experience value. After all, conventional standard brick algorithm does not take into account the equipment wear and tear, sheet material thickness of the situation Different thickness determines the different bending factors such as 1mm cold rolling fold 90 degrees and 2mm cold rolling fold 90 degrees Our actual situation is 1mm coefficient is 1.8 2mm coefficient is 3.5 The same angle 90 degrees is a bending factor of 60 degrees is 1/2 of the bending coefficient of 45 degrees is 1/3 of the bending coefficient of less than 30 degrees according to the different thickness of the buckle or buckle a 0.5 Material and plate thickness as different materials, the bending coefficient is different The bending radius is related to the bending machine. The standard single V or double V is even the default value of the other V slots. But there are customers who need to be too small or a large bend radius will be specific to the analysis Too small bend radius, our approach is to plan the groove to bend, so that the bending radius is very small, almost vertical right angle bending Too large bending radius, the upper mold can be used on the corresponding arc on the mold (note that the upper arc of the R is the inside of your bending R, if the outside R according to the outer R minus a plate thickness to determine the model) Or a large R30 50 or more, you can use a split bend, which requires the calculation of the cut-in angle and the last knife angle, as well as the size and angle of each knife There is a part of the length of this I think a lot or machine equipment and related to our machine a long time 1.5mm stainless steel over 1m according to the case will not use 8mm mold bending
- Q: Stainless steel wire drawing board, polishing plate, mirror the difference between the three
- Stainless steel wire drawing refers to: stainless steel wire drawing is a stainless steel surface like a filamentous texture, this is just a stainless steel processing technology. The surface is matte, carefully look at the top of a trace of a trace of texture, but can not touch out than the general bright stainless steel wear, looks more on the grade of some. Drawing process will be to a certain extent, the loss of stainless steel plate thickness, generally 0.1 ~ 0.2mm. In addition, because the human body, especially the palm of the hand has a relatively strong oil and sweat secretion, stainless steel wire drawing board often touch will leave a more obvious fingerprints, need to regularly scrub. Stainless steel polishing plate refers to: stainless steel polishing plate is polished by polished stainless steel bright plate, this kind of polishing board is generally not high brightness, but also according to the blurred figure. Stainless steel mirror panel refers to: stainless steel mirror panel industry, said the dual 8K plate, also known as mirror panels, grinding fluid through the polishing equipment in the stainless steel plate surface polishing, so that the brightness of the mirror as clear as the mirror. Stainless steel mirror panel from the K number generally: 6K 8K 10K 12K these kinds. From the requirements of the coefficient points are: the general grinding 8K high Pu 8K ordinary grinding 8K fine grinding 8K ultra-fine grinding 8K these types, of course, are getting better and better. Uses: mainly used in building decoration, elevator decoration, industrial decoration, decoration and other stainless steel products. From the difference, the stainless steel wire drawing board is a long strip of lines covered with stainless steel plate. While the polishing plate is cast into a certain brightness of the stainless steel plate. And stainless steel mirror panels, can be collectively referred to as glass-like stainless steel mirror panels.
- Q: How much does the ring do the ring?
- Do ten ring certification is mainly to see if you are doing a type of ten rings or two rings, if you do here for the purpose of ten rounds of tender, it is recommended that you can do a type of ring certification. You need to do the EIA, but also to prepare the early data. I was in OKorder million Germany to do the ten ring certification, then in order to bid, so do anxious, a month to get the card
Send your message to us
Floor Panel- Superimposed floor panel,Floor board ,Superimposed floor slabs
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 5000 m²
- Supply Capability:
- 20000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords