Fesi for Mining separation Si15
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Fesi for Mining separation Si15
Specifications
1 Type: 15#
2Size: 48mesh 200mesh 48D 270D 0-3mm
3We can do CIQ & SGS quality certification according to customer requirement
Applications
1 Milled Ferro Silicon 15# is a magnetic ferro silicon produced in electric arc furnaces and subsequently milled to size ranges required. In addition, Milled Ferro Silicon contains aluminum and titanium which enhances its resistance to corrosion.
2 Milled Ferro Silicon 15# is used in slurry density applications for heavy media separation and sink-float processes. Powdered Ferro Silicon is an accepted medium for the gravity separation of minerals, aggregates and metals with a specific gravity of approximately 2.0 to 4.0.
3 Milled Ferro Silicon 15# is used extensively in the dense media separation process in both the metal recycling and mining sectors.
Chemical Content
FE | Si | Ti | Al |
70-85% | 12-18% | 0-8% | 0-3% |
Data Sheet
Product Designation(mesh) | +48 | +65 | +100 | +150 | +200 | +325 | -325 | ||
Particle Size(micron) | Percentage by mass | ||||||||
48MESH | 0-6 | 0-8 | 6-14 | 14-22 | 17-25 | 22-30 | 14-22 | ||
65MESH | 0-4 | 0-6 | 3-11 | 11-19 | 15-23 | 25-33 | 23-31 | ||
100MESH | 0-2 | 0-4 | 0-6 | 80-90 | 0 | 0 | 0 | ||
200MESH | 0 | 0-2 | 0-2 | 0-4 | 4-12 | 30-80 | 0 | ||
48D | 0 | 0-2 | 1-9 | 10-18 | 14-22 | 27-35 | 27-35 | ||
65D | 0 | 0 | 0-2 | 0-6 | 4-15 | 29-33 | 47-55 | ||
100D | 0 | 0 | 0-2 | 0-3 | 0-7 | 25-33 | 61-69 | ||
150D | 0 | 0 | 0-1 | 0-1 | 0-4 | 16-24 | 73-81 | ||
270D | 0 | 0 | 0 | 0-1 | 0-3 | 5-13 | 85-93 | ||
0-3MM | -- | -- | -- | -- | -- | -- | -- |
FACTORY:
- Q: Does the hard alloy belong to the composite material?
- Grain refinement can improve both the hardness and toughness of the material. Hard alloys and cermets belong to particle reinforced composites, which change the size of hard phase and have great influence on the properties. In this paper, the preparation process of cemented carbide and cermet raw powder with different thickness is optimized, and two sets of materials with the same original chemical composition and different grain size are prepared by vacuum sintering technology.This is not how I suggest you go to Baidu search Suzhou haokai metal material limited company to ask it!
- Q: What kind of cemented carbide is the most wearable?
- Carbide wear is due to the grain size and the cobalt content determines the finer granularity of cobalt content is lower, the higher hardness and lower hardness should be mentioned is the selection of wear-resistant hard alloy not only the hardness to see the use of general cutting hard alloy material with YW2 a relatively high hardness but if the working conditions impact operations more frequently if it should take into account its toughness but the toughness and hardness is conflicting under such circumstances can choose the class YG fine grain alloy
- Q: Carbide grades, properties and applicable ranges
- The commonly used cemented carbides are mainly based on WC, and are classified into the following categories whether or not they are added to other carbides:(1) tungsten cobalt (WC+Co) cemented carbide (YG);It consists of WC and Co which has higher flexural strength, toughness, good thermal conductivity, but heat resistance and poor wear resistance, mainly used for processing cast iron and nonferrous metals. YG hard alloy fine grain (such as YG3X, YG6X), in the same amount of cobalt, the hardness, wear resistance than YG3 YG6 high strength and toughness is poor, suitable for machining hard cast iron, austenitic stainless steel, heat-resistant alloy, hard bronze.
- Q: Hello I remember carbide knives have several classifications As if it were not the same as it is now, can you tell me the same and different models as before? What material can they make?
- YT15 (P10) = 91 for hardness of carbon steel and alloy steel continuous cutting and semi refined car finishing. Intermittent cutting when finishing. The cyclone car wire, the semi finish and finish milling, rough and fine hole expansion. <o:p></o:p>YT14 (P20) = 90.5 hardness suitable for carbon steel and alloy steel uneven surface roughing the whole continuous cutting, interrupted cutting is the semi refined car and finishing, the rough milling, casting hole reaming etc.. <o:p></o:p>YT5 (P30) = 89.5 for hardness of carbon steel and alloy steel [including forging. Rough parts for stamping and casting. Rough planing, half fine planing, rough milling and so on. <o:p></o:p>YG8 (K30) = 89 for hardness cast iron, nonferrous metals and alloys, rough turning, non-metallic materials, uneven surface and intermittent cutting the rough planing, rough milling, drilling hole and deep hole reaming. <o:p></o:p>YW1 (M10) = 91.5 for heat resistant steel material hardness, strength of steel, stainless steel and alloy steel and other hard steel processing, is also suitable for ordinary steel, machining of cast iron.<o:p></o:p>YS25 (P25) = 90.5 for hardness of carbon steel, cast steel, high manganese steel, coarse high strength steel and alloy steel, milling and planing. <o:p></o:p>YG6X (K10) = 91 for hardness of alloy cast iron. Finishing and semi finishing machining of cast iron. <o:p></o:p>YS8 (M05) 92.5S for hardness is more than or equal to the iron-based, nickel based superalloy, high precision machining of high strength steel, finish machining of chilled cast iron and heat-resistant stainless steel, high manganese steel, hardened steel. <o:p></o:p>YG8N (K20K30) = 90 for hardness rough machining of cast iron and non-ferrous metals, is also suitable for the finishing of the rough machining of stainless steel. <o:p></o:p>YT30, YS30, YG6A, YG3, YG3X, YW2, YD777, and various non-standard products.
- Q: What kinds of carbides are there? How should we choose in production?
- Basically divided into four major categories: YG, YW, YS, YT.YG is cast iron, nonferrous metal, base alloy steel.YW is made of stainless steel and base alloy steel.YS is the finishing of high strength steel, steel and cast steel.YT is the rough processing of steel and cast steel.
- Q: What kinds of carbide knives do you have? Write out its main functions and uses.
- (3) tungsten tantalum cobalt (WC+TaC+Co) cemented carbide (YA);The addition of TaC (NbC) on the basis of YG cemented carbide improves the hardness and strength, thermal shock resistance and wear resistance at room temperature, high temperature, and can be used to process Cast Iron and stainless steel.(4) tungsten, titanium, tantalum, cobalt (WC+TiC+TaC+Co) and hard alloy (YW), such as W1, W2 and so on.On the basis of YT cemented carbide, TaC (NbC) is added to improve the flexural strength, impact toughness, high temperature hardness, oxygen resistance and wear resistance. Both can process steel, but also the processing of cast iron and non-ferrous metals. Therefore, it is often called universal cemented carbide (also known as universal cemented carbide). At present, mainly used for processing heat-resistant steel, high manganese steel, stainless steel and other difficult materials.
- Q: What are the differences in performance between cemented carbide cutting tools and PCD cutters (polycrystalline diamond)?
- Different cutting objects, PCD cutter durable, but cutting some materials may not be good on the PCD
- Q: Tungsten steel could be used to do is hard alloy knife?
- Of course you can need what specifications of tungsten steel knife
- Q: Why carbide fracture?
- Besides the material is very important, different material by using corresponding domestic and imported tungsten steel, it also has the very big difference.
- Q: Is it hard to make carbide cutting tools for aluminum alloy?
- High speed tool steel is essentially tool steel, but heat resistance is betterHard alloy is made of tungsten carbide, titanium carbide materials such as superhard materials. From the hardness and red hardness, high speed tool steel paima couldn't catch up. Although the name as "alloy" two words, it is actually a kind of metal ceramic.
Send your message to us
Fesi for Mining separation Si15
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords