12mm-63mm PE/PP pipe production line/electrical threading pipe production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
12mm-63mm PE/PP pipe production line/electrical threading pipe production line
Brief Introduction
Raw material: PE/PP
End product: PE/PP pipe
Pipe size: 12mm-63mm
Main extruder: SJ65 Single Screw Extruder
Main motor: 37kw
Linear speed: 2-10m/min
Configuration
pe/pp pipe machine
Hot air drying hopper | 1 set |
SJ65 single screw extruder | 1 set |
SJ20 extruder for color marking | 1 set |
Mold | 1 set |
Vacuum forming tank | 1 set |
Haul-off and cutter | 1 set |
Stacker | 1 set |
Main Technical Parameter
Main Extruder | SJ65 single screw extruder |
Main motor | 37kw |
Color marking line extruder | SJ20, 1.1kw |
Hot air drying hopper | 15L, 200kg |
Hopper blowing power | 0.37kw |
Hopper heating power | 10.5kw |
Vacuum forming tank length | 6000mm |
Vacuum pump power | 4kw |
Water pump power | 2.2kw ×2 |
Mobile motor | 1.1kw |
Haul-off linear speed | 2-14m/min |
Haul-off motor power | 1.1kw ×2 |
Quantity of caterpillar chain | 2 |
Cutter motor power | 2.2kw |
Application
PE/PP pipe production line is composed of Main Extruder, Extruder for color marking line, Mold, Vacuum Calibrating Tank, Haul-off Cutter, Stacker, and auxiliaries like hot airy drying hopper, automatic loader. It is mainly used for producing PE/PP pipe which is widely used in
1. gas, oil transmission and distribution pipeline
2. urban and rural drinking water pipeline
3. sewage drain pipe
4. liquid material conveying pipeline in chemical industry, food, pharmacy, papermaking, metallurgy industries
5. agricultural irrigation pipe
6. post and telecommunication line, electric cable protection casting pipe, etc.
- Q: Why will the extruder frequency shift stop?
- Because the frequency converter is out of order, you can look at the fault record parameters of the inverter.
- Q: Can PC and PP be extruded together with two materials in an extruder?
- No co extrusion, PC polycarbonate, PP polypropylene, two kinds of product structure is not the same, not the same chemical composition, viscosity and liquidity is not the same, processing temperature and processing technology is also very different, and two kinds of products, so not incompatible, CO extrusion.
- Q: Comparison of injection molding machines and Extruders
- Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.
- Q: Where is the Huangyan extruder machine?
- You want to see what type of mold processing, but Masino comprehensive, injection mold, blow mold, mold and so on can be developed.
- Q: What should be paid attention to in the daily maintenance of the extruder?
- Extrusion machine regular maintenance mainly has these aspectsdrive system(1) check the temperature rise of motor and oil tank, whether the bearing is overheated locally, the abnormal noise of motor and gear, oil leakage, radial circle of oil filter and spline shaft, and the contact gap with the end of screw.(2) regularly clean the oil filter and remove the dirt at the bottom of the tank, and lubricate the lubrication points regularly.(3) the new gear box has been filled with gear oil, and new oil will be replaced every 4000 hours after the operation.
- Q: Taper twin screw extrusion machining of plastic masterbatch? What ancillary equipment do you need?
- because itself is not suitable for the design of double cone, adjustment of the formula is the key.
- Q: Wire and cable extrusion machine extrusion die how to quickly adjust the core degree, how can I touch it by hand?,
- It depends on experience, and the lines made by squeezing it are solid. When you make the line, you can see the expansion and skewness of the material!
- Q: Who knows the structure of the big extrusion machine head (has cooled), smash what structure, model of plastic crusher?
- How big is it? Not too big. I suggest using a 40 or 30 too big block. You have to use a special break knot. There is a kind of broken engineering material. I wonder if you can find it
- Q: Now I want to do it How to change the equipment, please help tell your heroes ah!Used to do PVC pinch plate, now changed to PVC threading tube
- Do the plate equipment and pipe threading with PVC equipment, from the process, are PVC extrusion machinery, however, do different products, screw inside or something different, if you want to do product grade requirements is not high, can change, but stability is not so good ensure product.
- Q: How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
Send your message to us
12mm-63mm PE/PP pipe production line/electrical threading pipe production line
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 10 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
