Fireclay Brick - China Made Good Thermal Shock Resistance for Furnaces
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 m.t.
- Supply Capability:
- 10000000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Type:
We can supply High Alumina Bricks, Fireclay Bricks, Low Porosity Fireclay Bricks, Mullite Bricks, Corundum Bricks, AZS Bricks, Magnesite Bricks, Zircon Bricks,insulating Bricks etc.
Application:
Andalusite bricks are mainly used in the cooling wall of blast furnace, chemical and ceramic industry, the door of coke oven, or as the lining and checker of hot blast furnaces.
Specification:
Fireclay refractory brick
Product Index | N-1 | JN-40 | JN-42 | |
Al2O3 % | ≥42 | ≥40 | ≥42 | |
Fe2O3 % | ≤2.3 | ≤2.4 | ≤2.5 | |
Refractoriness °C | 1760 | 1760 | 1760 | |
Bulk density g/cm3 | 2.10 | 2.12 | 2.10 | |
Apparent porosity % | ≤22 | ≤24 | ≤23 | |
Refractoriness under load 0.2MPa°C | 1400 | 1380 | 1450 | |
Cold crushing strength MPa | 35 | 30 | 35 | |
Permanent linear chang % | 1500°C×2h | +0.1~-0.4 | +0.1~-0.4 | +0.1~-0.4 |
FAQ
Q3: Can you offer Door-to-Door delivery?
A3: Yes, but only for some countries such us U.S., UAE, Saudi Arabia, Iran, and Russia, etc.
Q4: What is the minimum quantity?
A4: There is no minimum order quantity. Depending on the item and processing, there may be a minimum production required, however we can offer a quotation based only on the quantity you need.
- Q: What are the application of used refractory brick pieces?
- It can be produced into refractory bricks again, as long as the quality is good. It is much more cost-effective than buying Bayerite.
- Q: Can refractory bricks be used when it cracks for 1cm
- 3, If the crack is caused by burning or drying, then it can't be used. While if the carck is caused by refractory brick molding, it still can be used. 4, the crack is caused by refractory bricks raw materials.
- Q: What are the weak points of clay bricks?
- SiO2 and Al2O3 in clay bricks form eutectic, low melting point silicates with impurities during sintering, and are surrounded by mullite crystals. Clay brick belongs to weak acid refractory products, it can resist acid slag and acid gas corrosion, and its resistance to alkaline material is a little worse. The thermal performance of clay brick is good, it is fast and cold. The clay brick refractory brick and be roughly the same, up to 1690~1730 DEG C, but the load softening temperature is 200 degrees Celsius above the low brick. Because clay bricks contain crystalline Mullite with high refractoriness, they contain nearly half of the amorphous glass phase of low melting point.
- Q: What kind of refractory brick is suitable for 24*28m rotary kiln of 5,000 tons?
- 24~28 meters belongs to the transitional zone, magnesia spinel brick or silicon carbide brick (Series)
- Q: Refractory brick, high alumina brick, magnesia chrome brick, magnesia brick, clay brick, which type of brick has the highest refractory temperature?
- It depends. if high alumina brick is used in kiln, its temperature is above 1700 degree, clay brick is between 1500 degree to 1750 degree, magnesia bricks and magnesia-chrome bricks are about 1500 degree to 1650 degree.
- Q: Is there any special requirements for the building blocks of the smoke and gas wells, how about the refractory bricks?
- There are no special requirements. Not necessarily need refractory bricks, red bricks are ok. The building size of the flue is according to the smoke exhaust rate.
- Q: What are the differences between sintered bricks and refractory bricks?
- Easily weathered. There is no obvious difference in the usage between fired pavingbricks and refractory bricks; sintered bricks are generally used for residential road and landscape engineering, they do not fade; refractory bricks are used for all kinds of kiln constructions in plant: It is not anti-freeze (when the temperature is below the zero degree, the brick will easily "blister" in the saturated state), the reasons are high compressive strength and high temperature zone' heat insulation and so on. Fired pavingbrick is a powerful vacuum extrusion type. Fire suppression road brick is high temperature furnace brick, which is not suitable to be used as road brick. Its characteristics are: Wear resistance and freeze-thaw resistance (the anti freeze-thaw cycle of brick is more than 50 times in saturated state), non weathering, sidewalks, short service life. Sintered brick belongs to the building material, refractory brick belongs to the industrial kiln material, which is easy to moss
- Q: can Methanol burn refractory brick?
- The upper part of the radiation chamber of the methanol oven is made of ceramic fiber, and the lower part is generally used refractory brick.
- Q: What kinds of annealing furnace refractory bricks there are?
- But the energy saving effect is good, but also can use lightwight heat insulating brick, but the price is higher than that of clay brick
- Q: does Kyrgyzstan have the refractory brick to build tunnel kiln, whose specifications are 390,235,11, 240,120,60.
- Domestic standard brick has no brick in this specification. only can be customised. Otherwise only have 230 * 65 * 114.
Send your message to us
Fireclay Brick - China Made Good Thermal Shock Resistance for Furnaces
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 m.t.
- Supply Capability:
- 10000000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
