Auto-climbing bracket ACB100 & ACB50
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Auto-climbing Bracket ACB100 & ACB50
The power of the auto-climbing formwork is the hydraulic system, which includes the oil cylinder
and two commutators. The commutators can control the climbing of climbing rail and the bracket.
The steel rail and the bracket can inter-climbing, so the whole system will climb up steadily.
Cranes are not needed during the construction. It’s easy to operate, highly efficient and safe. It’s
the best choice for the construction of high buildings and bridges.
There are mainly two types of standard auto-climbing brackets, ACB-50 and ACB-100, the figure
means the push power of cylinder with unit of KN.
Characteristics:
◆ Perfect load bearing anchor system
Anchor system is the most important supporting part. The system is made of five parts shown
below. Thereinto, tensile bolt, V-climbing cone and washer can be taken out for reusing after the
concrete pouring finished.There are two kinds of anchor systems,A & B. A is matched with single
anchor shoe and B is matched with double anchor shoe.
◆ Crane-independent
Crane-independent forming, striking and climbing speeds up the work procedures on the
construction site and also makes them independent of each other. This means the planned
sequences can be maintained along with guaranteeing high productivity levels. The crane can
therefore be used for other tasks.
Hydraulic system is mainly made of two commutators,
oil cylinder and power distribution system.The
commutators can control the climbing of climbing rail
and bracket.
◆ High bearing capacity and safe
The stable working platforms are able to carry large loads, e.g. the storage of reinforcing steel
for the next climbing section. Generously-sized working platforms, the well thought-out design for
handling very high wind loads and the patented control function of the climbing mechanism are
some of the special details contained within the comprehensive safety concept.
◆ Platforms adjusted to suit the angle of inclination
The horizontal working areas thus created provide safe and comfortable conditions for
reinforcement work, shuttering and striking, concreting and finishing.
◆ The ACB formwork system can climb not only vertically but also slantways, the largest angle is
18 degrees.
◆ The system can climb up wholly or separately. The climbing process is steady, synchronous
and safe.
◆ The bracket will not fall to the ground until the construction is finished, the field will be saved
and the impacting breakage will be reduced (especially the panel).
◆ The system will furnish omnidirectional platform, the construction organizations don’t need to
set up additional operation platform.
◆ The error of structure construction is small and easy to correct.
◆ The climbing speed is fast, the construction course will be quickened.
◆ The formwork can climb itself and cleaning work can be done in the same situs , the used times
of tower crane will be greatly reduced.
- Q:Is the car seat with lumbar support adjustable?
- It is better to find a mat what to deal with the first look, and slowly find the factory and this opportunity to change it. Also not for this function to give up the favorite models!
- Q:JGJ128-2000 door type steel scaffolding specifications only adjustable adjustable screw extension of the base of the relevant provisions of the top of the screw extension of the length of no provisions, but in the specification check the inspection items to check the extension of the screw extension length. What is the standard?
- JGJ128-2000 (JGJ128-2000) Section 9.1.4 of the door type steel pipe scaffolding used as a template support and full of scaffolding, adjustable base adjustment screw extension length should not exceed 200mm. When more than 200mm, the design value of a mast bearing capacity, that is, this specification (5.2.1-5) type Nd should be adjusted according to the adjustable seat extension screw length correction: extension length of 300mm, should be multiplied by the amendment Coefficient 0.90, more than 300mm, should be multiplied by the correction factor 0.80. The height of the template support frame should be adjusted with adjustable jacking.
- Q:Why 2013 BMW 320LI no waist support regulation, and now 2014 models are still not, as a luxury brand is difficult to understand
- Because it is low-end BMW models, like the 7 series of these have
- Q:BMW 3 Series driver seat waist support how much money
- Outside for more than 300 dollars, not processing, 4S shop almost nothing 1000.
- Q:The permissible range of the top support of the template
- At present generally only in the use of the exposed part of the length of a 200mm above the argument, in the template specification and door scaffolding norms have a few words.
- Q:What does the car support for the waist?
- Should be placed on the waist of the seat that seat, support the waist, the seat is more comfortable
- Q:What is the range of adjustment for the full range of scaffolding?
- Bracket vertical control vertical pole vertical and horizontal bar level, the vertical deviation of the whole frame shall not be greater than h / 500 (h for the pole height), but the maximum does not exceed 20mm;
- Q:Support on why there is adjustable support and support the set position, that is, where to put any place can not put?
- JGJ 162-2008, Fasteners for fastener steel scaffolding "JGJ130-2011 has been clearly defined in the template support pole must be set U-type top care. As long as it is to support the pole will put, and adjustable section may not be greater than 200mm.
- Q:Yee Jun Edition Octavia with waist support adjustment?
- Waist support and only the power seat of the tube thing, manual useless.
- Q:As the gym did not squat rack, with Smith machine waist twist discomfort, so use the reclining push the practice of squatting, from 40 kg to the current 85 kg. Can this continue to practice it?
- Instead of using an adjustable bench press, raise the bar of the barbell as a squat and do not carry the barbell from the direction of the bench to avoid danger (it may be tripped when retreated). The other squat use of the weight is usually larger, it is recommended in the other side of the bench (in the figure written on the three-point) to press the barbell or sit on the individual, so that the shelves overturned (I was knocked once).
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Auto-climbing bracket ACB100 & ACB50
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords