Cat8 Certification

Hot Products

2.54 Pitch IDC Socket Of Oppress

250W CNBM Monocrystalline Silicon Panel for Home Using

Cover Plastic Cover SRE2

1.778mm Pin Connector Single Row

2.54 Pitch Idc Connector

RJ45 Connector Boots For UTP STP

2MW CNBM Monocrystalline Silicon Cell From China Facotry

Cat6A SSTP(PiMF) Patch Cord Cat7 Cat8 Patch Cable

Cable Glands

Q Series DC Power Supply Mitsubishi QY81P Model 32 Point Source Output

FAQ

i just bought the connector today i installed the software and i tried to connect my ds in the wifi settings on pokemon platinum but it just keeps searching and searching and searching. have i done something wrong? have i missed something? please help i was so exited it was an early christmas present i gues.

DS needs to connect to a router not just to a wifi usb. To connect to a usb wifi hub then you would need to set up an adhoc network on the computer that has the usb connector attached and also share the internet. Was the usb conenctor bought just to connect the ds to a computer with already an internet connection, if it was it would have been better to get a wireless router. Try posting again and explain your setup a little better as in how you have internet access at the moment and how you aret rying to connect the ds to where?

I have a 1997 Toyota Previa. I failed a smog check and the mechanic gave this reason: timing connector doesn't ground for ignition timing to be checked. He said the Check Engine Light is supposed to come on when the connector is grounded, but it doesn't.Where/what is this timing connector, and does this have anything to do with the OBD-II connector under the driver's seat?

if your van failed smog check then you need to do a tune up spark plug,spark plug wires etc. Change O2 sensor and cat converter

i have 1994 325i i see a 22 pin (25 slots) OBD1 im trying to figure out if this connector is comaptible with my ODB.--------------------------------------------------------------------------------Item Description:Connect your OBD2 scanner and your vehicle with this 20 pin connector cable which is specifically for BMW's. Specifications:OBD2 Female BMW Connector4 5 19 (Signal ground) 7 17 20 (ISO 9141-2 K Line 15 15 (ISO 9141-L Line) 16 14 (Battery power) Brand new and unused BMW 20 pin connector to OBD2 female. (THIS ITEM IS ON OKorder ITEM# 220127580782)---------------------------------------------------------------------------orr where can i find something similar

Assemacher Tool and Supply Company Boulder Colorado. ASTNow do you know where that black round diagnosis connector is under the hood. Unscrew the cap if you find a PAC MAN shape in the center you found the connector plug in the adapter, plug in your scanner turn ingnition on read engine codes clear engine codes. AST tool will also reset service indicator when you do oil changes and maintences.

I bought a new Seiki HDTV recently and connected it to my Directv receiver via RCA connector (there is no HDMI input on the receiver for whatever reason) and it is in black and white and it's very pixel-y. My PS3 is connected to it with an HDMI cable and its picture is fine and colored and everything, so I figured it must be something wrong with the RCA connector. Anyone know what it could be?

HDtvs receiving SD signals over rca connectors look bad. You need to upgrade your direct tv box to an HD one with an HDMI output and hook it to your tv with an HDMI cable. You can use the r c a cable if you really want to, just be sure you are plugging it into a matching input on the tv. Your new tv may not have an obvious yellow (video) input, so look for the red/green/blue component video input and try one of those and use the red/white audio next to that input for sound.

I have a 120mm computer fan which doesn't have a regular fan header instead it takes in a 4 pin power connector directly from the power supply. How can I convert a 4 pin power connector into a regular 3 pin fan header. I have extra parts from broken fans and extra 4 pin power connectors so I can easily solder some stuff up, or if a adapter exists what is it called?

Well, if you want to do it manually, all you really need is the hot and the ground wire. The third wire is used as the fan controller. So if you have some extra wire there as you said and some connectors already, all you need is an electornic soldering iron and some solder and little bit of electrical tape. -----------------Red Wire (+) HOT -----------------Yellow Wire - Fan controller -----------------Black Wire (-) Ground Make sure you check your motherboard manual for the cpu fan connector + and - terminals. So long as you have the plus and minus terminals correct, then the fan controller wire is a no-brainer. Or, if you wish, you can just leave the yellow fan controller wire out and let the fan run at maximum speed all the time. If you have a good case fan with dual ball bearings, you need not worry about wearing the ball bearings out fast and getting a lot of racket or noise coming from the fan moving at maybe 4500 RPM. You could also get a molex connector from an old power supply and pull one of the wires out, there is are two blacks, a yellow and a red. All you really need is one black, one yellow and one red. If you know how to solder the rest is easy. Just get the plus and minus terminals correct.

I want to plug my Macbook pro into my Computer monitor and also my TV. I am going to be using it as a portable desktop. I just wanted to know how I can plug it in? I have a thindebolt port and I'm not sure if it can be used as a minidisplay port. thanks guys.

BlazeVideo HDTV participant is an entire-featured digital Analog television utility answer which you will observe, checklist, pause, replay stay television/teletext software or hear to digital FM radio on your workstation. helps DVB-T, DVB-S, DVB-S2, DMB-TH, CMMB, ISDB-T, ATSC worldwide digital television standards and chum, NTSC, SECAM Analog television standards, BlazeVideo HDTV participant helps maximum conventional television enjoying cards / television Tuners / USB television Dongles with Mircosoft BDA rigidity on marketplace. BlazeVideo HDTV participant additionally acts as your multi-media center, with greater advantageous video and audio high quality, and helps DVD, VCD, SVCD, and maximum conventional media archives playback.

I am trying to see if anyone can tell me what is this connector is used for? under front bumper of 98 taurus there is a power connector ( power outlet) where you can plug a power cord.I have no idea what is it for? thx

As Doug said an engine heater, for very cold climates. They're used by quite a few people in cold weather as an engine that is warm starts a lot easier than an engine that is 30 below zero. In Alaska everyone uses them, some use two and the parking slots, in town, even have outlets to plug into. It's strange though that it would be an outlet (female) connector. If it is a four to seven pin female plug, it could be that the car was towed behind a Motor Home, at one time. The umbilical cable to connect the car to the Motor Homes light system uses a cable that requires at least four pins. Depending on what functions are used, such as auxillary braking systems, the cable could be up to seven wires.

I need to know if this will work on TV, I like if I put a movie in my computer can I watch on my TV screen. also do I need something else.Thank you:

At a minimum, I would imagine, you might be able to do it using WMP as a player, connecting the ouput of your video card with an s-video connector to the s-video input on your tv, and the audio output (2 stereo jacks or composite) from the pc to the audio input of your tv.