Slitting and Cut to Length Machine Line No.5
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Slitting and Cut to Length Machine Line No.5
General Information：
High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.
Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.
It is takingthe place of brick to be a main material for building now.
Processing flow is as following:
Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging
Technical Data：
1. Coil Thickness：0.3-4mm
2. Coil Width：300-1800mm
3. Coil Max. Weight：30 T
4. Coil I D：φ508-φ800mm
5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa
- Q: Slitting machine; batten; place
- The fixed position of the metal slitting machine when feeding trolley material should pay attention to the coordination and discharge power, prevent raw off injured foot. At the same time to ensure the position of the metal material in the uncoiler must be accurate.
- Q: There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?
- The photoelectric proximity switch on the top photoelectric proximity switch or buffer pit at the top of the opener is damaged, and the silicon steel sheet can not be detected near the signal and should be replaced.
- Q: Technical parameters of the slitting machine
- Strip material: metal plate, plain carbon steel, stainless steel, galvanized plate, aluminum strip, copper strip, cold rolled plate, hot rolled plate, etc.;
- Q: What is a striping machine?
- What kind of slitting machine, flat knife or double-edged sword?. Laminating machine or slitting? This question also concerns the thickness of the original roll, for example, the original roll is 1 millimeters thick
- Q: What is the difference between CNC slitting machine and slitting machine?
- CNC cutting machine, cutting machine and roll a large, similar to what size will directly cut. CNC slitting machine, then the main cut, there is a shaft discharge, and another shaft winding, the middle through the knife.
- Q: Slitting machine, pc0.8 mm coil, why have rough edges?
- See if your device's line speed matches previous settings. Is it online faster?. In the past, the torque was gained by changing the coiling moment motor.
- Q: How to adjust the pearl cotton separator?
- The adjustment can be achieved by the tightness of the hand button at the lower end of the paper holder.
- Q: How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
- One is single-sided corrugated machine, first made of single-sided corrugated cardboard, and then through a single glue car processing, made into different structures and corrugated cardboard.
- Q: The belt machine used for gluing buckles lacks power
- Check the air flow meter, throttle position sensor, crankshaft position sensor, camshaft position sensor and oxygen sensor signal is normal.
- Q: Is the tape on the tape slitting machine a good one at the back or a good one in front?
- It is not easy to see the situation of the mother roll from the back. The advantage is that the finished product can be made clear at a glance. If your mother roll is larger, it is recommended to use the following one
Send your message to us
Slitting and Cut to Length Machine Line No.5
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
