Slitting and Cut to Length Machine Line No.1
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
General Information：
High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.
Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.
It is takingthe place of brick to be a main material for building now.
Processing flow is as following:
Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging
Technical Data：
1. Coil Thickness：0.3-4mm
2. Coil Width：300-1800mm
3. Coil Max. Weight：30 T
4. Coil I D：φ508-φ800mm
5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa
- Q: There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?
- The overload of the uncoiling machine and the overcurrent alarm of the converter.Solution, turn off the main power supply of the electronic control system and restart it.
- Q: Why does a bar break occur in a bar splitting machine?
- The bending caused by the rapid movement of the correcting device: if the movement of the rectification is too fast during the process, the side of the contact with the rectification will be partially extended and bent.
- Q: What are the features of a metal slitting machine?
- A slitting machine refers to a device for slitting and slitting wide volumes of material, each of which is used in accordance with its own material characteristics
- Q: The technique of arranging knives in a slitting machine
- Slitting machine will be the whole volume or raw materials for fixed length cutting.
- Q: Slitting machine, pc0.8 mm coil, why have rough edges?
- Improper use of winding and winding motor series. Fast series of changing motor.
- Q: How to adjust the pearl cotton separator?
- Adjust the conveyor belt, arbitrary adjustment of one, so that the pearl cotton tape machine with the film roll paper side of the drilling alignment;
- Q: How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
- One is single-sided corrugated machine, first made of single-sided corrugated cardboard, and then through a single glue car processing, made into different structures and corrugated cardboard.
- Q: The belt machine used for gluing buckles lacks power
- Check the air flow meter, throttle position sensor, crankshaft position sensor, camshaft position sensor and oxygen sensor signal is normal.
- Q: What is the difference between a slitter and a slitter?
- When cutting, he also allows the edges to be cut and spread automatically. Strip machine, he used a stepless speed control, in the cutting of the time is relatively smooth.
- Q: Is the tape on the tape slitting machine a good one at the back or a good one in front?
- If you are concerned about the volume from the front. Mainly depends on your mother roll size, whether to change regularly, the quality of mother roll, how about, do not pay attention to its condition. Very few people ask this, I may not consider the full, you have the right to reference!
Send your message to us
Slitting and Cut to Length Machine Line No.1
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
