Slitting and Cut to Length Machine Line No.4
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Slitting and Cut to Length Machine Line No.4
General Information：
High speedslitting and cut to length can cut steel with thickness from 1mmto 16mm, if noneed slitting thickness up to 30mm.
Sandwichpanel, as a new building material，shows excellent performance oninsulation. We can design the line to make different kinds of panels inappearance, for wall panel and roofing panel with various joint designs.
It is takingthe place of brick to be a main material for building now.
Technical Data：
1. Coil Thickness：0.3-4mm
2. Coil Width：300-1800mm
3. Coil Max. Weight：30 T
4. Coil I D：φ508-φ800mm
5. Material: carbon steel platewith σb≤550Mpa、σs≤350Mpa
Processing flow:
Carry coil→loadcoil→de-coiling（pressingguide +opener）→entry、roughlevel→cutting→transition→guide→slitting (waste winding) →loopingstorage→pre-separating, damping→recoiling→packing→discharging→guide→leveling→fix size (end platefeeding)→cutting→discharging
- Q: Why does a bar break occur in a bar splitting machine?
- The bending caused by the rapid movement of the correcting device: if the movement of the rectification is too fast during the process, the side of the contact with the rectification will be partially extended and bent.
- Q: How do metal slitting machines cut out knives?
- The cutting skills of the slitting machine in the bar machine, and its Pai skills, mainly depends on the specific situation. If it is a good quality slitting machine, then it will be equipped with cutter software to carry out the correct arrangement.
- Q: Technical parameters of the slitting machine
- The machine speed: 100~180m/min; (the actual processing speed of the design according to customer requirements of precision materials)
- Q: The technique of arranging knives in a slitting machine
- Fixed length slitting control is divided into two types: static and dynamic cutting.
- Q: Slitting machine, slitting machine looper (pit cause analysis) in the strip of varying lengths
- Relatively thin thickness of the strip, less winding diameter, winding speed is relatively small. This resulted in different lengths of strip pit the phenomenon.
- Q: Slitting machine, pc0.8 mm coil, why have rough edges?
- Improper use of winding and winding motor series. Fast series of changing motor.
- Q: How to adjust the pearl cotton separator?
- The adjustment can be achieved by the tightness of the hand button at the lower end of the paper holder.
- Q: How is the gap between the cutter and the cutter in the metal slitting machine measured without damaging the knife?
- A variety of equipment will be the entire corrugated cardboard production process organically combine, so that its continuous production. The traditional methods of combined production of more units and single machines not only have high production efficiency, low labor intensity, but also operate centralized control, which is simple, safe and low noise. The most important thing is that the corrugated paperboard produced is of high quality.
- Q: What is the difference between a slitter and a slitter?
- When cutting, he also allows the edges to be cut and spread automatically. Strip machine, he used a stepless speed control, in the cutting of the time is relatively smooth.
- Q: Is the tape on the tape slitting machine a good one at the back or a good one in front?
- It is not easy to see the situation of the mother roll from the back. The advantage is that the finished product can be made clear at a glance. If your mother roll is larger, it is recommended to use the following one
Send your message to us
Slitting and Cut to Length Machine Line No.4
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 2000 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
