PVC MDF laminated Wooden Door VISION PANEL
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 set
- Supply Capability:
- 20000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
DOOR SIZES
SINGLE DOOR STANDARD SIZE - 1100mm width, 2200mm height.
DOUBLE DOOR STANDARD SIZE - 2200mm width, 2200mm height.
The width and height given for doors are rough standard sizes.
All Above mentioned steel doors are powder coated to Client's approved colour.
VISION PANEL SIZE
150mm width, 600mm height.
300mm width, 300mm height.
STANDARD DOOR VARIANTS
No Hardware
Standard Handle,lock case ,hinges,Glass as per requirement.
Panic Hardware,panic bar,hinges,door closer,Glass as per requirement.
External access - Panic bar,Panic bolt,hinges,door closer,Glass as per requirement.
All hardware quoted is Consort brand,UK.
NOTE: HARDWARE MENTIONED IS NOT FIRE RATED.(FIRE RATED HARDWARE IS POSSIBLE ON DEMAND)
The door width is 46 mm.
Frame jamb is 150 mm,either SRF or DRF frame type.
Sheet thickness is 1.5mm for frame.
Sheet thickness is 1.2mm for door leaf.
- Also available : Accoustic Doors, Sliding Doors, Wood finished Steel Doors.
- Custom made Doors also avilable to meet your specifications.
- Our Fire Rated Steel Doors and Frames are in compliance with UL for safety standard ANSI/UL 10B Fire Test of Doors Assemblies.
-These doors are used in warehouses,factories,buildings(door for stairways),etc.
- Q: Finished aluminum alloy doors and windows more than one square meter. Is the kind of ordinary, flat open the door, sliding window
- 160 can get it
- Q: I am installing laminate floor and there is metal door threshold. The metal door threshold is slightly less thick than the wood, in addition, I dont believe it lifts up. What is the best course of action to put the laminate against this threshold? The wood is perpendicular to the threshold. Thank you
- You can remove the threshold, there should be screws or nails holding it in place. You can then finish the flooring and reapply the threshold. You may want to see about a different style of threshold, 'edges' vary. You will need to watch the 'height' of the threshold if it changes, the door may not fit. Then you can trim the door bottom slightly (or sand down) with the door off the hinges. If it is a door to the outside you may be able to adjust the door bottom weatherstrip piece to allow for any extra thickness.
- Q: You know when you have like a wooden door and a metal door is their like a certain name to call them
- Are you talking about storm doors/screen doors?
- Q: Engineering materials, aluminum doors and windows need to check it, I am a party unit?
- If the tender list to the test fee can require the construction unit to send re-inspection, the general aluminum doors and windows rarely sent to the re-inspection, there are manufacturers of inspection reports and certificates can be followed by a supervisor is signed with the material acceptance report. General aluminum alloy doors and windows mainly look at the thickness of aluminum alloy, specifications, glass and so on up to the requirements.
- Q: Aluminum door lock how can be fixed and solid
- The formation is directly related to the staff of the equipment, a card reader, electronic door locks, go out button, alarm sensors and alarm horns and so on. The middle layer is the controller to receive information on the personnel of the underlying equipment, compared with the information stored in their own to make a judgment, and then issued a processing information. The top layer is a computer, a number of controllers through the communication network with the top of the computer connected to form the entire building access system.
- Q: The door is wooden, but the door frame is metal (I found out when the screw wouldnt go in no matter how I hammered it). Is there a way to install a hasp to put padlock on? (Are there screw drivers for metal surfaces?) Or is there any other way to have the door locked without having to installing a cylinder lock?
- You need to drill a hole first with a metal twist drill bit. Get a drill bit that is the same size as the screw shank (the solid part below the threads - the hole must be smaller than the diameter of the threads, so there is material for the threads to bite into), mark the location of the holes for the hasp on the frame, and drill the holes to the depth of the screws. Then attach the hasp.
- Q: Into the door is a metal door or special door
- Into the door does not belong to the special door, but not all of the door into the door are metal doors.
- Q: it is a metal kitchen door,with a large window that i dont want to leave open
- You'll have to drill pilot holes for the screws. Use a drill bit that is slightly smaller than the screw. You'll want to use a better screw than what comes with the curtain rod, those are usually flimsy and snap easily.
- Q: about 3 days ago, now theres a bump there and hurts when i press it , shouldnt swelling been went down? also hurts a bit when i try to open my hand wide open. i was angry and stupid dnt tell me about anger management plz lol
- I've punched a brick wall when angry so I know what you mean. You may have sprained your hand get it checked out by your doctor. I sprained mine lol but, hey no gym for a week or two ;) lol Put ice on it if it doesn't go down I'd see a doctor :)
- Q: Why,In dry weather, people walking on nylon carpets may get a shock if they touch a radiator or a metal door?
- Many valuable opinions already for this
Send your message to us
PVC MDF laminated Wooden Door VISION PANEL
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 set
- Supply Capability:
- 20000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
