Power Stacker CS1232FFL/SP - Pedestrian - polyurethane tyre

Ref Price:

Loading Port:: Shanghai

Payment Terms:: TT OR LC

Min Order Qty:: 1 unit

Supply Capability:: 1 unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Scissor Lift

Self-propelled Scissor Lift

Crawler Mounted Platforms

spider lift 21M

Moveable material lifting machine series

Self-Propelled Rough-Terrain Scissor Lift Material Hoist Lift Table JCPT

Mobile Aluminium Work Platform (dual mast)-GTWY -2000

Sleeve Type Aerial Work Platform ASP SERIES

PRODUCT NAME:Power Stacker CS1232FFL/SP

PRODUCT INTRO

Compact construction, stable capability, wide-field mast with full free lifting system
Power Stacker
The hydraulic system is imported from Europe, it enhance the efficiency and safety.
Smooth travel and lift with excellent controls reduces product damages and increases productivity.
Lift limit switch operates at maximum lift height to shut off pump motor.
A heavy-duty 24-volt electrical system provides good travel and lift speeds.
High quality hydraulic pump assures very little noise, maximum efficiency and durability.
Drive units is equipped an electromagnetic brake that is spring applied and electrically released. The brake is activated by the control handle position. The handle is ergonmically designed with a raise, lower and horn button.
Speed automatically reduces when driving the fork at a height of 12" or higher.
Built with a Germany ZF driving wheel . It has more power and allows it to work continuously for a much longger time.
The CURTIS electronic controller helps provide plenty of low end torgue while increasing the motor and battery life.
Foot pedal reduces fatigue.
Excellent stability in operation.
Min. fork height 80mm
Conforms to EN1726-1 and EN1175-1

Residual Capacity at different lifting height

1KG=2.2LB 1INCH=25.4MM

Up to h3 mm	ACTUAL CAPACITY (Q) kg
Load centre distance (C)mm	600	700
2500	1200	600
3200	1000	500

Identifica tion	1.2	Manufacturer’s type designation		CS1232FFL	CS1232SP
	1.3	Drive:electric(battery or mains),diesel, petrol,fuel gas,manual		electric
	1.4	Type of operation:hand,pedestrian, stand ing,seated, order-picker		Pedestrian
	1.5	Load Capacity /rated load	Q (t)	1.2	1.2
	1.6	Load center distance	C mm	600	600
	1.8	Load distance, centre of drive axle to fork	X mm	765	765
	1.9	Wheelbase	y mm	1342	1342
Weights	2.1	Service Weight	Kg	975	965
	2.2	Axle loading, laden front/rear	Kg	1065/1110	1065/1100
	2.3	Axle loadings, unladen front/rear	Kg	700/275	700/265
Wheels, Chassis	3.1	Tyres:solid rubber, superelastic, pneumatic, polyurethane)		polyurethane
	3.2	Tyre size, front		230x75	230x75
	3.3	Tyre size, rear		80x70 1)	80x70 1)
	3.4	Additional wheels(dimensions)		124x60	124x60
	3.5	Wheels, number front/rear(x=driven wheels)		1x+2/4	1x+2/4
	3.6	Track width,front	b10(mm)	570	570
	3.7	Track width,rear	b11(mm)	395	395
Basic Dimensions	4.2	Lowered mast height	h1(mm)	2105	2105
	4.3	Free lift	h2(mm)	1580	100
	4.4	Lift height	h3(mm)	3115	3115
	4.5	Extended mast height	h4(mm)	3670	3670
	4.9	Height of tiller in drive position min./max.	h14(mm)	864/1287	864/1287
	4.15	Lowered height	h13(mm)	85	85
	4.19	Overall length	l1(mm)	1997	1997
	4.2	Length to face of forks	l2(mm)	847	847
	4.21	Overall width	b1(mm)	795	795
	4.22	Fork dimensions	s/e/l(mm)	60/180/1150
	4.25	Width over forks	b5(mm)	575	575
	4.32	Ground clearance, center of wheelbase	m2(mm)	25	25
	4.33	Aisle width for pallets 1000x1200 crossways	Ast(mm)	2494	2494
	4.34	Aisle width for pallets 800x1200 lengthways	Ast(mm)	2441	2441
	4.35	Turning radius	Wa(mm)	1650	1650
Performance Data	5.1	Travel Speed, laden/unladen	km/h	5/5.5	5/5.5
	5.2	Lift speed, laden/unladen	mm/s	97/164	97/164
	5.3	Lowering speed, laden/unladen	mm/s	128/120	128/120
	5.8	Max.gradient performance, laden/unladen	%	6/12	6/12
	5.1	Service brake		Electromagnetic
E-Motor	6.1	Drive motor rating s2 60min	kw	1.5	1.5
	6.2	Lift motor rating at s3 15%	kw	2.2	2.2
	6.3	Battery acc. To DIN, no		3VBS	3VBS
	6.4	Battery voltage, norminal capacity	V/Ah	24/210	24/210
Others	8.1	Type of drive control		MOSFET Control
Others	8.4	Sound level at driver’s ear acc.to EN12053	dB(A)	67	67

Related Products

Q: The hydraulic platform is compared with the normal lift platform: Double protected leg structure, work safer, and can be close to the working face lift. The machine is the answer for you!!

Q: When the hydraulic platform drops, it feels very shaken and unbalanced. Please answer?: Can you adjust the flow rate to slow down the same amount of pressure and the decrease is much faster than the increase. This does not know that the valve is connected to the solenoid valve, which may be the overflow valve or the balance valve The oil tank has no refueling mouth and oil outlet?

Q: What is the reason for the automatic lowering of the hydraulic platform: The hydraulic lift can rise steadily or maintain position because of the pressure oil in the cavity.

Q: The characteristics of hydraulic platform: Hydraulic lifts and elevators are both elevations, but the biggest difference is the journey. The advantage of hydraulic lift is smooth, especially in the initial end of the lifting, but again good hydraulic elevator also amounted to less than 10 m or a few meters, and the elevator is similar to hoist, well make up for the disadvantages.

Q: There are several reasons for the hydraulic cylinder oil leak on the elevator: Oil cylinder in and out tubing joint cracking; (I've seen a lot of this in practice.) 2) the sealing damage of the piston rod with the piston rod is caused by the pull of the piston cylinder. 3) cooperate with cylinder liner piston rod out end seal is damaged, this is caused by long-term use of seal aging more, also has a lot of end cover on is too hard to seal extrusion is damaged, there is a lot of domestic manufacturer of hydraulic cylinder design is not reasonable cause (mostly in order to save costs)

Q: Does the shear fork lift stand belong to special equipment?: It belongs to special equipment, the manufacturer must have special equipment production qualification "special equipment manufacturing license" to be able to produce the sale shear fork lift machine. The products of the manufacturer without relevant documents are not eligible.

Q: The characteristic of shear fork platform: Shear fork lift platform is mainly used in the logistics industry, production lines, lifting, loading and unloading goods to floor between basement, can also be used to lift stage, lifting work station, etc. The product has a stable structure, low failure rate, reliable operation, safe and efficient and easy to maintain.

Q: How is the small electric shearing fork lift designed: Fixed elevating platform is a kind of high and low stability, which is widely used for the transport of goods by the high difference of production line. The material is up and down. Adjust the height of the workpiece when the workpiece is assembled; Top feeder: Lifting up parts when large equipment is assembled; Material on large machine tools; The warehousing and loading and unloading facilities shall be equipped with the loading and unloading of goods such as forklift truck.

Q: The home is decorated, make a tatami mat the platform should pay attention to what aspect?: The second is to notice whether the product has a secure clamping system. Most of the products on the market are mechanical clamping system, which is low in safety, and the system is too resistant to it. Best choice is the electronic control system, because it will through the electronic system induction to the resistance changes, more than a certain value will stall, electric and automatic recovery (electronic resistance setting values are very sensitive, high security), such as task of children. The third is, of course, the manufacturer and the brand, the good manufacturer and the brand make the product more reliable, which is not to be said in detail.

Q: Put a large beaker of water on a horizontal platform and put a light glass upside down in the water: The inside of the large beaker is raised, the pressure on the surface of the large beaker is larger, and C is right. The pressure of the bracket on the glass is downward, the pressure of the gas is rising, the glass gravity is constant, the pressure of the bracket is greater for the glass, and the D is wrong

Send your message to us

*Email

*TEL

*Quantity

*Unit