Full Electric Walkie Scissor Aerial Work Platform(hydraulic motor)-JCPT-HD
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Model | Unit | JCPT0808HD | JCPT1008HD | JCPT1012HD | JCPT1212HD |
Rated capacity | kg | 380 | 230 | 450 | 320 |
Extend platform Rated capacity | kg | 113 | |||
Max number of people | 2 | ||||
Max working height H1 | mm | 8000 | 10000 | 10000 | 12000 |
Max platform height H2 | mm | 6000 | 8000 | 8000 | 10000 |
Overall length B | mm | 2480 | |||
Overall width C | mm | 810 | 810 | 1150 | 1150 |
Over height(rail unfold) | mm | 2210 | 2340 | 2340 | 2470 |
Over height(rail fold) A | mm | 1750 | 1880 | 1860 | 1990 |
Working platform size D | mm | 2270×810 | 2270×810 | 1270×1120 | 1270×1120 |
Platform extend size | mm | 900×800 900×1120 | |||
Ground clearance (stowed) | mm | 100 | |||
Ground clearance(lifting) | mm | 19 | |||
Wheelbase | mm | 1870 | |||
Min turing radius(inside) | mm | 0 | |||
Min turing radius(outside) | mm | 2190 | |||
Motor | V/kw | 3/24 | |||
Drive speed(stowed) | km/h | 3.5 | |||
Drive speed(lifting) | km/h | 0.8 | |||
Raising/Falling speed | sec | 22/34 | 22/40 | 30/33 | 30/38 |
Battery | 4×6V/210Ah | ||||
Charger | V/A | 24/25 | |||
Maximum gradeability | % | 25 | |||
Max angle | º | 2/3 | |||
Tyre | mm | Ф381×127 | |||
NW | kg | 1950 | 2100 | 2300 | 2730 |
Standard Configuration
-Proportional controller
-Automatic pot hole protection system
-4x2 drive
-Emergency stop button
-Emergency descending button
-Horn
-Working chronometer
-Transport standard forklift hole
-Extended platform
-Charge protection
-Self-lock door
-Total excursion
-Tracelessness tyre
-Self-actuating brake system
-Oil pipe explosion protection system
-Fault diagnosis system
-Tilt protection
-Motor reset protect
-Buzzer
-Folded rail
-Strut bar for safe overhaul
Optional Configuration
-AC power source connected to platform
-Working lamp
-Rotary strobe light
-Overweight sensor
-Air scoop connected with platform
- Q: The hydraulic platform is compared with the normal lift platform
- Light weight, good maneuverability, suitable for one-man operation. The special mast strap-roller device, which is stable and stable.
- Q: What is the use of a silk pole elevator?
- The product can be widely used in metallurgy, machinery, chemical industry, construction, water conservancy, textile, medical, culture and health, etc. Such as mechanical processing of the weight of the lifting platform, the turning device and the plastic processing machine, etc. Installation and maintenance of the climbing ladder and the tool lift frame, the motorcycle maintenance platform, the hot liquid pouring; Architectural aspects for mobile devices and composite templates, adjustable Windows, walls, walls, etc. Cultural hygiene can be used for elevating stage, adjusting swimming pool floor height, adjusting operating table height, etc.
- Q: How does a button in the PLC control the elevating platform
- To be safe, at least two buttons.I hope my answer will help you.
- Q: How does hydraulic platform change sealing ring, how to operate
- Because the concrete structure of hydraulic cylinder is different, the order of disassembly is different, and it should be judged according to the specific situation.
- Q: What is the reason for the automatic lowering of the hydraulic platform
- The non-leakage of pressure oil is the key factor for the non-drop, so check the one-way valve
- Q: How to automatically lift up and lift
- There is a manual lifting table, with the hand rotating black knob, lifting the platform clockwise, reducing the counterclockwise elevation.
- Q: There are several reasons for the hydraulic cylinder oil leak on the elevator
- The sealing part of the seal is worn out to buy two oil seals according to oil cylinder model to change to be good also a few dollars
- Q: Tomb raider 9 research base elevator to go to go to go to go to the order to pry the gear not to go down to go down to go down the card 3 to break up
- There are four of them, four of them. See the white climbing wall outside the elevator? Find a way to burst open a hole in the iron wire and climb to the fourth gear. There was no order in this gear, four of them were done, and the elevator fell down.
- Q: The characteristic of shear fork platform
- Shear fork lift platform is mainly used in the logistics industry, production lines, lifting, loading and unloading goods to floor between basement, can also be used to lift stage, lifting work station, etc. The product has a stable structure, low failure rate, reliable operation, safe and efficient and easy to maintain.
- Q: On the principle of hydraulic lifting platform, using the foot switch control, when stepping on hydraulic pump, hydraulic platform, depressed when, what is under the control of the hydraulic cylinder pressure?
- When stepping down, the oil line to the left of the cylinder is connected, and the oil cylinder on the right side of the cylinder is returned to the oil and the platform rises. When lifting the foot, the oil line to the right of the oil cylinder is connected, and the oil cylinder on the left side of the cylinder is returned to the oil port and the platform drops. The commutator valve can be divided into several, such as: stop, positive, negative or positive. The above is the simplest of all, which can actually be used to implement sequential actions of multiple hydraulic cylinders through sequential valves, or more complex actions.
Send your message to us
Full Electric Walkie Scissor Aerial Work Platform(hydraulic motor)-JCPT-HD
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords