Plastic Tubes HDPE Corrugated Pipe Steel Wire Reinforced PE Pipe
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 2000 m
- Supply Capability:
- 50000 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
hdpe corrugated pipe steel wire reinforced pe pipe
1)Distinguished comprehensive performances
2)Safe and reliable ring stiffness
3)Strong load capacity to resist improper burst
4)good sealing and low cost of construction
Others features same with PE pipes
Anticorrosion, anti-ultraviolet, smooth internal surface, impact resistance, toughness, Nonpoissonous, abrasion resistance, long operating lifeas long as 50 years.
The application of hdpe corrugated pipe
1) Agricultural irrigation and water conservancy project. |
2) Industrial zone construction. |
3) Park and Golf course construction. |
4) Residential construction. |
5) Road,plot construction |
6) Power supply, the street light installment . |
7) Many situations instead of steel pipe and other pipes. |
hdpe corrugated pipe physical characters:
Items | Index | Testing Method | |
Ring stiffness. KN/m2 | SN8 | ≥8 | GB/T9647-2003 |
SN12.5 | ≥12.5 | ||
SN16 | ≥16 | ||
Impact resistance | TIR≤10% | GB/T14152 | |
Peel strength,(20°C±5°C),N/cm | ≥70 | Refer to appendix A of CJ/T225-2006 | |
Ring flexibility | No fracture and delaminating | GB/T9647 | |
Oven test | No and drying crack | Refer to 8.4.5 of CJ/T225-2006 | |
Tensile strength(N) of joints | ≥1460 | GB/T8804 | |
Creep rate,% | ≤2 | GB/T8042 |
- Q: i recently got started with oil paint, and some of my tubes are leaking quite a bit. i seal the cap well, and there are no holes or anything in the tubes. i read that putting the tubes under extreme heat or sunlight can cause them to leak, but i do neither of these things.how do you prevent/solve this?
- Leaking okorder /... Both of these prevent the dreaded twist and crack that can open up a hole where paint can both leak and be exposed to air. Also treat the caps gently. Make certain to routinely clean off the paint that biulds up around the threads. Wipe this off as opposed to allowing it to dry forcing you to remove it with harsher methods like scraping or using a solvent. Be conscious of the way the cap feels when tightening it on the threads. Sense whether it has derailed or whether the threads are clogged. Paint can build up on the tube threads and/or the threads inside the cap. These caps are fragile and often strip or crack. If a cap gets stuck and the tube body begins to twist while attempting to unscrew the cap run the cap end under hot water until it loosens up. Avoid twisting the tube body. It will tear apart. It is a good idea to save the good caps of old used tubes when they are ready to be trashed. They are not all interchangeable but they might be and it is worth having some around. Replacement caps are not sold by themselves but if you catch a bad cap on a new tube you may have a replacement sent to you by the manufacturer if purchased directly. You could try asking for a complete tube of paint replacement from retailers. I have done both successfully.
- Q: water frezzes in tube fill icemaker, if I clear out it works fine a couple times and then frezzes up again.
- Defrost your freezer and you should be fine
- Q: What is the maximum length of plastic tubes?
- The maximum length of plastic tubes can vary depending on the manufacturing process and specific requirements, but it is typically several meters long.
- Q: How can I make a frosting tube?You know, the stuff you put frosting in squeeze it out?I want it to come out thin kind of so I can write Welcome homeCan't you like put it in a regular plastic baggy?But how do I make a nozel for it to come out of?...I need one within the next half hour. I Cannot go to the store fir anything..HELP
- They are both right! I just suggest you use a freezer bag, they are sturdier. I've used regular bags before only to have the seams pop half way through. Good luck!
- Q: How can the plastic pipe fall into the throttle valve?
- The valve on the throttle is basically a vacuum tube, one is EGR (waste gas recirculation), the two is the brake vacuum drum vacuum, and the three is the cold car speed
- Q: Are plastic tubes safe for children's toys?
- Yes, plastic tubes can be safe for children's toys, as long as they meet certain safety standards and regulations. It is important to ensure that the plastic used is non-toxic, durable, and free from sharp edges or small parts that could pose a choking hazard. Additionally, adult supervision should be present during playtime to ensure the safe usage of toys with plastic tubes.
- Q: I have a plastic container cage I D.I.Y.ed and was thinking of adding a few other D.I.Y.ed plastic containers to the cage but I need some tubes to connect them, I could buy some tubes but I wanted to see if anyone any ideas for cheap D.I.Y. tubes. If you can include links of examples it would be cool but don't worry if you can't. THANKS
- what about plastic vitamin bottles? they are often tube-like? btw, can def show u how to make fun tube hotel out of the core of toilet paper rolls tho... 1. save 3 or more toilet paper roll cores. 2. make some holes on top of the cores so that the mice can climb from one tube to another. 3. get double sided tape (or staple the tubes together if its not sticking) and attach two toilet paper cores together, with the holes on opposite sides of the core so the mice can climb. you can just stack them all together on top of one another and voila! toilet paper core hotels... lol ps. mice loves to chew on things so to grind their teeth to a good length so its perfect for a chew toy too.
- Q: What are plastic tubes made of?
- Plastic tubes are made of various types of polymers, such as polyethylene, polyvinyl chloride (PVC), or polycarbonate, which are molded into tube shapes to provide strength, flexibility, and durability for different applications.
- Q: I'm so scared ):What should I be doinglooking out for?worst case scenario?HELP
- The plastic tubes could have gotten lodged in his intestines somewhere. Best thing you can do is take him to a vet.
- Q: How do you put the plastic pick up tube on to the brass pick up tube on a briggs and straton carburetor?
- You need the proper size tubing, and it just slides over, and a clamp holds it in place.
Send your message to us
Plastic Tubes HDPE Corrugated Pipe Steel Wire Reinforced PE Pipe
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 2000 m
- Supply Capability:
- 50000 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords