Mylar Lamination Film- 40mm Width Metalized PET/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
Product Structure
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
● Aluminum foil – LDPE
● Aluminum foil- PET- LDPE
● Clear Transparent PET-Aluminum foil – LDPE
● Aluminum foil-Metallized PET- LDPE
● Metallized PET- LDPE
Product Application
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
Product Advantage
Light weight
• High manufacturing accuracy
• High strength
• Small inertia resistance
• Strong heat dissipation ability
• Good visual effect
• High reflective insulation
• Heat resistant, water proof, stable at high temperature;
• Environmentally friendly, no smell and not-toxic;
• Smooth and clear surface;
Product Packing
1. Waterproof paper then PVC shrinking Film
2. Kraft paper only
3. Woven cloth
4. Kraft paper or Water Proof Film then Metal/wooden pallet
5. (Also as your request. )
Product Remarks
1. The data above are typical results and subject to change without notice.
2. Tolerance: Weight and Thickness: ±10%; Width: ±3mm;
Length: Cut Roll & Log Roll ±0.3m, Jumbo Roll ±0.5%.
3. The products should be stored at room temperature and kept from wet and heat source.
4. It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, and free of grease and oil.
5. The user should take test and do trial-application on the above products before coming into application so as to witness and ensure suitability for user’s special purpose and technique.
Product Data Sheet
PROPERTIES | UNIT | VALUE | TEST METHOD |
Basic weight | gsm | 33.5 | ASTM D646 |
Thickness | mic | 23.2 | ASTM D646 |
Tensile strength: M. D. X. D. | N/15mm | 13.5 13.5 | ASTM D882 |
Delaminating Values | N/15mm | 1.5 | ASTM D904 |
Reflectivity of foil surface | % | 95 | ---------- |
Temp. Resistance | -40°C 130°C | No Delamination No Delamination | ASTM C1263 |
Water vapor permanence | ng/N.s | 1.15 | ASTM E-96 |
Product Picture
FAQ
1. What is the product keeping conditions?
The Aluminum Foil Facing should be stored at room temperature and kept from wet and heat source.
2. What is the guarantee years of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
3. What is the delivery time of the order?
In the purchase of product within four working days, we will arrange the factory delivery as soon as possible. The specific time of receiving is related to the state and position of customers. Commonly 7 to 10 working days can be served.
- Q: Why do you put plastic film on the paved road?
- Plastic film does not have special requirements, as long as it can be covered with water to prevent evaporation. In the cold season construction to cover the mats and other things to keep the temperature.
- Q: Plastic film has eyes, how to make up?
- Thick film is damaged, the available hand suture repair. First, wash and dry the old film, then cut a piece of film with the same texture on it. Use a needle or a sewing machine to mend a patch at the skin hole, or sew it up at the seams.
- Q: How much plastic film can melt?
- Polyvinyl chloride (PVC), referred to as PVC, is a polymer of vinyl chloride monomer in the presence of peroxide, azo compounds, initiators, or under the action of light and heat, polymerized by radical polymerization mechanism. No fixed melting point, softening at 80~85 degrees, 130 degrees to viscoelastic state, 160~180 degrees of temperature began to change into viscous flow;
- Q: Building floor pouring why plastic film underneath?
- This is a relatively old waterproof and moistureproof way, the effect is good, and now waterproof materials are multifarious, most of the materials are less than the effect of doing so
- Q: What's the thickness of plastic film 5C?
- The thickness of the film is 0.5 mm, the plastic film 5C model bubble film is based on high pressure polyethylene as the main raw material, and then add brighteners, openings and other accessories, by 230 degrees or so high temperature extrusion Blister Blister products.
- Q: What happens when the friction coefficient of PE plastic film becomes larger?
- The film base itself smoothness bad; not with extrusion composite slip agent, sticky film extrusion PE, the friction coefficient is larger;
- Q: Is the foundation covered with film or damp proof powder?
- 1, I do not know what is the principle of moistureproof powder?. It is estimated that it is additive. But not added to mortar, doubt the function.2, the film will be better, but the follow-up construction is easy to damage, durability is limited, it is better to do a waterproof.3, on the foundation moistureproof, equal to did not do. It is no use crossing a block of water in the middle of the pool. Damp proof should be done below ground level.4, I don't think the film is better than the traditional damp proof layer. Can the height on the ground, construction (brick), can play a role of natural moisture barrier; or on the ground part of the wall construction waterproof isolation layer.
- Q: Why are more transparent plastic films used in flower sheds instead of glass?
- The cost of plastic film is low and the cost of glass greenhouse is too high.The plastic greenhouse is economical, practical and low in cost, and can be chosen according to the needs of production and planting. Plastic film is better for profit maximization.Glass greenhouse skeleton is usually made of galvanized steel pipe or aluminum alloy light steel, in the process of cultivation, the service life is the longest, but the cost is very expensive. If the flowers are not special rare flowers, it will not use the glass greenhouse.
- Q: Why plastic film greenhouse can keep warm?
- Because the heat is hard to escape through the plastic film, the temperature difference between the upper and the lower of the greenhouse can not be enlarged, and the convection is very small, so that the heat can be kept warm. The key here is the plastic film is very similar to shun donkey, sun radiation from the inside, with stubble, almost without shelter; and the heat from the inside out is the inverse stubble, resulting in heat insulation.
- Q: How to deal with plastic film greenhouse joints?
- Sticking method. Is mainly used for vinyl chloride resin adhesive bonding repair plastic PVC film, polyethylene film of polyurethane adhesive available repair, sometimes small hot hot rolling steel blade available.
Send your message to us
Mylar Lamination Film- 40mm Width Metalized PET/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
