Stretch Wrap Film Transparent Stetch Silicone Food Wrap Film Meat Wrapping Film Stretch Wrap Film
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 roll
- Supply Capability:
- 1000000 roll/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Introduction of Stretch Wrap Film
Stretch Wrap Film is made of 100% pure sofe LLDPE raw material.
Application of Stretch Wrap Film
Stretch Wrap Film is available in hand-applied and machine formats for product moisture proof, anti-dust, fastening and protecting etc. Our stretch film are widely used in following fields, such as outer packing of corrugated box or pallet, packing of loose and small products together, packing of bare machine etc.
Advantage of Stretch Wrap Film
Economical and Practical
Excellent extension, fight to impale
Excellent ability of binding
Price: According the size and the order quantity
Packing of Stretch Wrap Film
One 20GP container can be loaded about 10-15tons.
By sea or by air all available.
Size of Stretch Wrap Film
Thickness:20-200um
Width:30-300cm
Length:1500-3000m
Notice: Special products made as per customer requirements.
Pictures of Stretch Wrap Film
Specification of Stretch Wrap Film
| Thickness Range | Tensile Strength | Elongation at Break | Angle Tear Strength | Impact Ability of Pendulum | Tackness | Light Transmission Rate | Frog Density |
| Micron | Mpa | % | N/mm | J/mm | N/cm | % | % |
| 15-17 | 37 | 250500 | 120 | 0.14 | 3 | 93 | 2.4 |
| 18-20 | 38 | 300600 | 120 | 0.15 | 3 | 92 | 2.5 |
| 21-25 | 39 | 300600 | 120 | 0.17 | 3 | 91 | 2.6 |
| 26-30 | 40 | 400650 | 120 | 0.19 | 3 | 90 | 2.7 |
| 31-35 | 41 | 450700 | 120 | 0.21 | 3 | 90 | 2.8 |
Remarks
1. The data above are typical results and subject to change without notice.
2. Tolerance: Weight and Thickness: ±10%; Width: ±3mm;
Length: Cut Roll & Log Roll ±0.3m, Jumbo Roll ±0.5%.
3. The products should be stored at room temperature and kept from wet and heat source.
4. It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, and free of grease and oil.
5. The user should take test and do trial-application on the above products before coming into application so as to witness and ensure suitability for user’s special purpose and technique.
We have organized several common questions for our clients，may help you sincerely：
FAQ
①How about your company？
A world class manufacturer & supplier of castings forging in carbon steel and alloy steel，is one of the large-scale professional investment casting production bases in China,consisting of both casting foundry forging and machining factory. Annually more than 8000 tons Precision casting and forging parts are exported to markets in Europe,America and Japan. OEM casting and forging service available according to customer’s requirements.
②How to guarantee the quality of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
③How long can we receive the product after purchase?
In the purchase of product within three working days, We will arrange the factory delivery as soon as possible. The pecific time of receiving is related to the state and position of customers.Commonly 7 to 10 working days can be served.
- Q: Plastic film has eyes, how to make up?
- Carry on with a soldering iron or electric iron. This method is only applicable to PVC film. Repair, to shop in the film on a flat surface, cutting a hole slightly larger than the similar films, first put the two connected with a damp clothWe completely clean and dry cloth to dry film shop in the hole, then a slightly thick glass paper on top, with an electric iron in glass paper gently move, make the interface film heated to melt, when coolingAfter that, the two layers of film stick together.
- Q: What is the density of the common PE films?
- Its density is about 0.92g/cm3. Low density polyethylene film transparency and good sealing performance, waterproof, moisture-proof; low tensile strength, tensile elongation, easy wrinkled, thin film below 0.03mm, tension control should be small, and all the tension to a constant, especially easy to deform when heated, causing difficulties in color. Therefore, when drying, the film surface temperature should not be too high (within 550C). According to the film forming process, can be divided into blown film, cast film (IPE) (CPE), several low foaming film etc.. IPE thin film tensile strength and opening than CPE film, with positive printing, can be used for food bags, clothing bags; CPE thin film thickness uniformity, surface gloss, transparency and thermal sealing is better than PE, but positive and negative printing, but the production cost is higher. CPE film is mainly used as the inner layer of composite bags and cosmetics, pickles and pastry packaging; low foaming film decorative, thick texture, not easily tensile deformation, using positive printing, as New Year paintings trademarks and hand bag etc..
- Q: Is it good to use PP bag or plastic film?
- With asbestos mesh (general dish pack more use of this media) direct contact with the disk, the relative effect is better
- Q: Would you please put a plastic film on the bottom of the tent and put a plastic film on the top of the tent for lightning protection?
- Rain proof, moisture proof, lightning protection, and no eggsWell, I think that if you are not dead or unlucky, lightning not be split into your head. Then you need to be more careful about what happens to you when the lightning hits another place.
- Q: Is it possible to lay a plastic film between the roof slab and concrete for waterproofing purposes?
- The roof is waterproof, or it is recommended to use professional waterproof material to do, in the prefabricated board paving finished, first with ordinary cement mortar leveling the ground, and then start waterproof.Roof waterproof, it is recommended to use rigid waterproof + flexible combination of waterproof construction. Thus, the utility model not only has the advantages of firm adhesion of the base surface, strong puncture resistance, high strength, but also can resist the stretching deformation of a certain extent of the base surface, and can meet the waterproof requirement of the roof for long time to be exposed to sunlight, rain and erosion.The specific construction method is to brush K11 waterproof slurry, flexible type, and then do a mortar waterproof agent protection layer, so that it can achieve good waterproof effect!Special reminder, the standard construction is a guarantee of good results, so must be in accordance with the requirements of standard construction, brushing thickness, height, interval time, etc., need attention.
- Q: Can ultraviolet light penetrate transparent plastic film?
- There are only a few types of plastic, such as PMMA, PC, PEA, which can penetrate ultraviolet light. The general film is not made of these plastics and cannot be transmitted through ultraviolet rays
- Q: How to identify the model of plastic greenhouse film?
- Should be 7.5-8 meters, we span 6 meters, with 7.5 meters, just right, both sides can be stuck, 8 meters, a little more.
- Q: How to quickly remove the plastic film on the floor tiles?
- 1, ceramic tile daily cleaning can choose detergent, soap and other cleaning. 2, with soap, add a little ammonia and turpentine mixture, cleaning tiles can make tile more luster. 3, polished brick should be regularly waxing, the time interval is 2-3 months is appropriate. 4, such as brick surface scratches, can be applied in the scratch of toothpaste, wipe with a dry cloth can be repaired. 5, brick and brick crevice can be used regularly decontamination paste to dirt, and then brush a layer of waterproof agent in the gap, can prevent mold growth. 6, tea, coffee, beer, ice cream, grease and other pollutants using sodium hydroxide or potassium bicarbonate solution. 7, ink, cement and other pollutants use hydrochloric acid, nitric acid and other dilute solution. 8, paint, paint and other pollutants use special cleaning agent.
- Q: Roof SBS waterproof fine stone concrete protection layer construction, the role of the separation layer?
- Cold sticky method is a kind of construction method which uses rubber modified asphalt cold adhesive to paste coiled material. This method is mainly used in the single layer waterproof structure and the laminated waterproof structure, and under the ordinary circumstances, the method of point sticking or strip sticking is adopted. The thickness of the coil must be cold adhesive. The use of cold adhesive should be painted in uniform, the control interval of cold coil coating and adhesive paving, application of hot method to deal with the overlapping part and coiled material parts.
- Q: What are the appliances for drawing plastic films?
- The tensile strength is divided into longitudinal and transverse directions. Plastic film material in a certain direction, through the tensile fixture test speed, tensile until fracture, showing the carrying capacity.
Send your message to us
Stretch Wrap Film Transparent Stetch Silicone Food Wrap Film Meat Wrapping Film Stretch Wrap Film
- Ref Price:
-
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 roll
- Supply Capability:
- 1000000 roll/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
