High Speed Leveling and Cut to Length LIne
- Loading Port:
- Xinggang Port
- Payment Terms:
- TT or L/C
- Min Order Qty:
- 1 set set
- Supply Capability:
- 100 set per month set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications of Leveling and Cut to Length Line
General Information of Leveling and Cut to Length Line
Cut to length line is used to cut metal with thickness range:0.3mm -40mm,width range: 300mm-2500mm steel coil to required length, change steel coil to steel sheet. This line is suitable for leveling aluminium and carbon steel coils.
Processing flow is as following:
carry coil→load coil→de-coiling(pressing guide +opener)→entry、rough level→guiding→leveling→cutting(with coding reader to set fixing length for cutting) →belt transmission desk→discharging
Technical Data of Leveling and Cut to Length Line
Manual Sheet Metal Shearing Machine Equipment Brief Introduction:
Cut to length line equipment, is used for cold rolled steel, galvanized steel, and hot rolled steel(Should clean the equipment after operation, preventing oxidized substance sticking on the rolls), going through precision NC Feeder to the shear machine,and cut the steel length you want.
Manual Sheet Metal Shearing Machine Compose of Leveling and Cut to Length Line
Coil Car→ Uncoiler→ Leveler→ Loop Control→ Parallelism bar → NC Feeder→Conveyer→Stacker→ Hydraulic Shear Machine
Come with: Hydraulic System, Pneumatic System, Lubrication System, Electronic System
1.Coil Car
We offer durable coil cars which are applicable in various industries for lifting coils .
2.Uncoiler
Holding the coil and uncoiling the coil, composed of four segments.
1)One sector cantilever with hydraulic expansion mandrel system.
2)Mandrel expansion range: Φ470-Φ530mm.
3)Pneumatic butterfly brake
4)Covered with Polyurethane to start uncoiling the strip, manually operation
5)The mandrel uncoiler base frame is made from ark-welded steel
3.Leveler
1)To Flatten the strip at processing speed
2)Mechanical Features
3)Pinch Rolls
4)Work Rolls
4.Loop Control
Using inductor to control the loop, make a good speed balance between leveler and NC Feeder
5.Centring Device
Using vertical roll on both sides to centre the strip Manual adjustment Centering Range
6.NC Feeder
ACS11KW Servo motor control, feeding the precise strip with high speed.
Touch Screen for user-friendly use.
Pinch Roll: 2pcs (42crMo, alloyed steel, surface heat treatment,chrome plated)
Control System: HMC+PLC Controller
7.Conveyer
Conveyer Construction: Combined by welded steel plate and steel.
8.Stacker
Stacker Structure: Use the steel and steel plate welding processing. make sure both sides of the pusher plate with a tailgate, let the pallet tidy.
9.Hydraulic Cut To Length Machine
1)Hydraulic Driven
2)Closely work together with NC Feeder
3)Gearing: Gear wheel driven the machine,
4)Cutter: Material SKD-11, HRC59o-61o, four sides of the cutter are all sharp for maximum economical usage.
10.Hydraulic System
A hydraulic cylinder, controlled by an electromagnetic commutation valve
11.Pneumatic System
The measurements of the cylinders correspond to ISO standards
12.Lubrication System
All the equipments have related lubrication system
13.Electronic System
1)Including main control table and secondary control table
2)Main components are from Japan Mitsubishi, Fuji... or the same level products
Payment Term and Condition of Leveling and Cut to Length Line
1 | Payment Term | 30% T/T in advance, 70% T/T before shipment |
2 | Delivery Time | Within 120 Working Days after receipt of the down payment |
3 | Warranty | 1 year and life-long maintenance |
4 | Installation and commissioning | Our engineer will go to make installation there, Buyer pay our engineer 100 USD /day, and provide accommodation, Visa and the round-trip ticket fee |
- Q:What is the difference between a slitter and a slitter?
- It is a kind of mechanical equipment used to cut wide width paper or thin film into many narrow materials. It is commonly used in paper making machinery and printing and packing machinery.Before the cutting machine of magnetic powder clutch speed is not high, because of high speed friction, in operation due to the magnetic powder to produce high temperature, shorten its service life, serious when the death card, make the machine run suffocate suffocate, bring very serious consequences for the production. Seriously affected production efficiency.
- Q:What is a striping machine?
- The first row of specifications is full size 580, second specifications (550+8+1.8), the lower is the first (550+8+1.8), the second is 580, 20, the two sides cut specification good flank is outwards, full size two good knife face.
- Q:There is a gap in the size of the strip machine, and the material is burr. Is the cutter axis beating or something else? How do you solve it?
- The photoelectric proximity switch on the top photoelectric proximity switch or buffer pit at the top of the opener is damaged, and the silicon steel sheet can not be detected near the signal and should be replaced.
- Q:Slitting machine; batten; place
- The fixed position of the metal slitting machine when feeding trolley material should pay attention to the coordination and discharge power, prevent raw off injured foot. At the same time to ensure the position of the metal material in the uncoiler must be accurate.
- Q:What is the function and classification of the slitting machine?
- The structure of the strip machine consists of uncoiling (unwinding), material positioning, slitting, slitting, coiling and winding
- Q:How do metal slitting machines cut out knives?
- If there is no, then the operator can only be based on some operational experience, etc.. However, it should be noted that for the blade clearance, it is necessary to control the good, so as not to affect the slitting effect.
- Q:What are the features of a metal slitting machine?
- The utility model is composed of an uncoiling machine (a discharging machine), a leveling machine, a material positioning device, a slitting equipment (a shearing device), a winding machine (a material collecting machine) and the like.
- Q:The belt machine used for gluing buckles lacks power
- The main reason is that the ignition advance angle is incorrect, the fuel pressure is too low, the intake system leaks, the throttle position sensor or air flow meter fails, the injector is not working well, and the EGR system is not working well.
- Q:The technique of arranging knives in a slitting machine
- Fixed length slitting control is divided into two types: static and dynamic cutting.
- Q:Why does a bar break occur in a bar splitting machine?
- The bending caused by the rapid movement of the correcting device: if the movement of the rectification is too fast during the process, the side of the contact with the rectification will be partially extended and bent.
1. Manufacturer Overview |
|
---|---|
Location | Hebei, China |
Year Established | 2008 |
Annual Output Value | |
Main Markets | 28.71% Domestic Market 16.39% Eastern Europe 14.26% North America 14.26% Southeast Asia 14.26% Africa 7.13% South America 4.99% North America |
Company Certifications | ISO9001:2008 |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Tianjin Port |
Export Percentage | 41% - 50% |
No.of Employees in Trade Department | 8-10 people |
Language Spoken: | Chinese; English |
b)Factory Information | |
Factory Size: | 10,000-30,000 square meters |
No. of Production Lines | Above 10 |
Contract Manufacturing | OEM Service Offered |
Product Price Range | Average |
Send your message to us
High Speed Leveling and Cut to Length LIne
- Loading Port:
- Xinggang Port
- Payment Terms:
- TT or L/C
- Min Order Qty:
- 1 set set
- Supply Capability:
- 100 set per month set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords