H.F pipe line 508mm pipe mill
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Material to be processed:Carbon Steel, Cold Hot Rolled pre slit strip coils of weld able grade with max. 0.2% carbon
Type of Production: * Round Tubes*Squar *Square and Rectangular Hollow Sections
Round Tube Outside Diameter: Min 219 Max 508mm
Square Hollow Section: Min 170 x170 Max 330x330 mm
Rectangular Hollow Section: Min 150x 200mm Max300x 250 mm
Tube Thickness: Min 3.0mm Max 18.0 mm (X70≤14mm)
Forming Line Speed: Max 30m/min (Square and Rectangular Hollow Shapes are produced at lower speeds depending on side to wall thickness ratio)
Tube Cut Length: Min 4 Max 15 meter
Length Accuracy: ± 3mm
V-shape pre-discharging table ( V coil stand)
Hydraulic charging wagon (coil car)
Hydraulic discharging machine (uncoiler).
Leveler & flattener
Shear and TIG Welder
Horizontal Strip Accumulator.
Forming, Welding, Cooling and Sizing Section.
Computer Flying Saw Cut-Off.
Driven Roller Run Out Table, Inspection table & Collectors.
Straightener
End Milling and Chamfering Machine
Baling Press
Solid State H.F. Induction Welder: 800 kW, Solid State Type(Vaccum Tube Type)
Rolls: Rolls are manufactured out of AISI D3 D2 E52100
Hydraulic Units
Electrical Panels
- Q: A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Yes, the width of the bearing plate can be a deviation from the length.
- Q: What is rolling forming processing?
- Ironing the surface of the workpiece with a raised micro wave crest to fill the concave micro troughs, thus changing the distribution of the peaks on the surface, and obtaining smaller surface roughness values.
- Q: Improvement in rolling forming process
- The utility model has the advantages of short service life, easy damage and high comprehensive use cost.
- Q: Introduction of roll forming process
- Roll forming began around 1960s in europe. Because of roll forming, the working model has the advantages of high production efficiency, saving material and increasing product strength.
- Q: What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Non bonding wear of rolled material (especially stainless steel strip, etc.)
- Q: What is the surface rolling forming machine process?
- Different from cutting, mirror rolling is a kind of plastic processing. Not only is the rolling workpiece surface roughness moment can reach Ry0.1-0.8 m, and the wear resistance of the surface hardening process has been improved at the same time fatigue strength also increased 30% advantages in cutting can not get.
- Q: Process mould for rolling forming process
- Rolling forming is more complicated and requires higher than rolling thread. The die design is based on the different shapes of the workpiece, the design of the rolling plate into a cross section or a few sections, can use synchronous type; also can use grading type.
- Q: Material and equipment for roll forming process
- Rolling process is a cold forging process, which can be used for rolling and forming a lot of materials. Among them, low carbon steel is a material commonly used in rolling forming, and non-ferrous metal is more suitable for roll forming.
Send your message to us
H.F pipe line 508mm pipe mill
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches