HG50 tube mill
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
HG50 Steel Pipe Making Machine
I. Summary
The Machine is intended for manufacturing round pipe of Φ20mm-Φ50mm with thickness of 0.8mm–3.0mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths.
Finished product will be of round, square or rectangular pipe.
II. The technical flow of the production line
{SteelTape}→→ Double-head un-coiler →→Strip-head Cutter and welder→→
Spiral Accumulator→→Forming section(Flattening unit +Main driving unit +Forming unit +Guide unit +High frequency induction welding unit +squeeze roller)+ De-burr frame →→Cooling unit →→ Sizing unit and straightener →→Flying saw under computer-control →→ Run-out table
III. Basic conditions:
a) Steel Pipe Specification
1. Pipe diameter: Ø20 –Ø50mm
Pipe Thickness: 0.8 – 3.0mm
2. Square & Rectangle Pipe: 15X15mm –40X40mm
Pipe Thickness: 0.8 – 2.0mm
3. Pipe Length: 6.0m – 9.0m
4. Length Tolerance: 0-6mm
b) SteelTape Specification
1. Material: Carbon steel (δb≤500Mpa, δs≤235Mpa)
2. Steel Tape: Inner diameter: Φ470-510mm
Outer diameter: Φmax=1500mm
Strip steel width: 60mm-160mm
Strip steel thickness: 0.8mm-3.0mm
The maximum weight: 1.5 tons
c) Electric installed capacity: appro. 400KW
d) Size of the whole line: appro. 45X5m
e) Line Speed: 40-100m/min
Forming & sizing section
4.1 Forming mill gearbox, universal joint
4.1.1 Mill entry flattener by five-roll passive levelling, one pair of sending roll, two pairs of vertical roll
4.1.2 Forming mill consists of:
- Driven stand: 7 sets (Horizontal)
- Driven stand shaft: Ø60mm
- Material of shaft: 40Cr
- Side roll stand: 8 sets(Vertical)
- Side roll stand shaft: Ø40mm
- Material of shaft: 40Cr
- Gear box & universal joint: 7sets
- Material of gear box: cast steel
- Material of gear: 20CrMnTi
4.2 Sizing mill gear box, universal joint
4.2.1 Sizing mill consist of:
- Driven stand: 5 sets (Horizontal)
- Driven stand shaft: Ø60mm
- Material of shaft: 40Cr
- Side roll stand: 5 sets(Vertical)
- Side roll stand shaft: Ø40mm
- Material of shaft: 40Cr
- Gear box & universal joint: 5 sets
- Material of gear box: cast steel
- Material of gear: 20CrMnTi
4.2.2 2 setsTurk’s head, with 4 rollers*2sets
4.2.3 One speed testing roller with air cylinder for CNC flying saw
4.3 Main motor: 100kW Model: Z4-250-31 1 set
Main reducer: 1 set
- Q:Cement pipe machinery and equipment how to work?
- The melting point of zinc is lower than that of steel, so when the steel melts, the zinc burns violently, so try the way to finish the zinc in the area where the galvanized or welded
- Q:What is the stainless steel pipe machine?
- Stainless steel with welding, the need for rapid cooling water, and through the three groups of grinding wheel surface grinding, so that the weld flat, no feel.
- Q:What kind of plastic pipe is divided?
- Plastic pipe is generally made of plastic resin as raw materials, adding stabilizers, lubricants, etc., to "plastic" approach in the pipe machine by extrusion processing.
- Q:What is the purpose of each mold of stainless steel pipe machine?
- In the use of stainless steel pipe machine widely used in stainless steel anti-theft doors and windows, staircase handrails, car exhaust pipe, muffler tail pipe, ship pipe, food hygiene tube, fluid pipe, water pipes, pressure stainless steel pipe, heat exchanger
- Q:The introduction of the pipe machine is
- The main pipe is divided into two major: one of which is a common high-frequency welded pipe machine, the other is a stainless steel pipe machine, high-frequency welded pipe machine is mainly used for the production of various iron pipes, water pipes, etc .;
- Q:What is the difference between galvanized welded steel pipe and galvanized steel pipe?
- The most commonly used is galvanized steel pipe. Galvanized welded steel pipe application is not very difficult to see
- Q:Pipe machine on the bearing what are the requirements
- This type of pipe machine is a continuous set of equipment that can be continuously welded into a pipe and straightened.
- Q:How does the pipe machine operate?
- Temporary maintenance in the shift and replacement process time to solve the normal maintenance as planned to complete; all maintenance should be planned, can not be carried out, the hidden dangers of the equipment should be forward-looking, can be done in a timely manner, and ready to deal with ready
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
HG50 tube mill
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
