Gaskets EPDM Rubber Ring O Ring DN1100 on Sale
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Description of Gasket :
Ginseal Spiral-wound gaskets comprise a mix of metallic and filler ma- terial. Generally, the gasket has a metal (normally carbon rich or stainless steel) wound outwards in a circular spiral (other shapes are possible) with the filler material (generally a flex- ible graphite) wound in the same manner but starting from the opposing side. This results in alternating layers of filler and metal. The filler material in these gaskets acts as the sealing element, with the metal providing structural support. These gaskets have proven to be reliable in most applications, and allow lower clamping forces than solid gaskets, albeit with a higher cost.
2.Features of Gasket :
1.A.Wound style gasket consists of four type:basic type,with inner ring,with outer ring,and with inner and outer rings. B.Heat exchanger wound style gasket:basic type and with inner and outer rings.
2. Normally matrial used:
A.Steel tape:08F,0Cr18Ni9(304),0Cr18Ni9Ti,1Cr18Ni9Ti(321),0Cr17Ni12,M02(316),00Cr17Ni14M02(316L).
B.(Cold roll)steel plate for inner and outer ring:Outer ring:mild steel,0Cr13 and 0Cr18Ni9
Inner ring:same as steel t
• Wide range of applicable working condition,high temperature and high pressure resistance,applicable to super low temperature and vacuum condition.Chemical resistant gasket is available under various medium,through change of composition of gasket.
• Strong stress compensation,stable and reliable sealing performance even under frequent pressure fluctuation condition.
• Perfect sealing performance.
• Normal requirement of flange surface finishing which contact with gasket.
• Easy installation and low pre-tightening stress of gasket.
3.Gasket Images:
4.Specifications of the Gasket:
1.A good compression ratio and elasticity.
2.With plastic appropriate, after pressing can adapt to the sealing surface and sealing surface uneven fill the gap, to ensure good sealing performance with the temperature and pressure in the system of alternating case.
3.With excellent corrosion resistance, not to be damaged in some extreme medium, does not have the expansion and contraction.
4.Under the condition of high temperature softening, does not creep; under the condition of low temperature hardening, does not shrink.
5.Have sufficient strength, when external load conditions, not be crushed; at high temperature, not blown out.
5.FAQ
Ask 1: Why some supplier give me the price much cheaper than you?
Answer:1.They wanna attract your attention,while you contact with them,they would raise the price by any reason.
2.They willn't provide the high qualities to you cause it had the cheap price.
Ask 2:What the MOQ?
Answer:The MOQ should reach 800 kilograms
Ask 3:Should i pay for it If some product need molds?
Answer:I'm afraid you should pay for it,However,We would return it back when we get the first order.
Ask 4:What's the delivery circle times ?
Answer:About 2 weeks and we would give the accurate time when we know the quantity.
Ask 5:What's the FOB port?
Anser:Our port are Shanghai and Ningbo usual.
Ask 6:Your price seems higher than others.
Answer:As you know,Price equals qualities.We have faith in our qualites.But it must be in the acceptable range
- Q: What's the difference between plastic and rubber?
- Plastic has good insulation for electricity, heat and sound: electrical insulation, arc resistance, heat preservation, sound insulation, sound absorption, vibration absorption, noise elimination, and excellent performanceAnd rubberRubber (Rubber): highly elastic polymeric material with reversible deformation. It is elastic at room temperature and can produce great deformation under very little external force. It can be restored to original state after removing external force. Rubber is completely amorphous polymer, its glass transition temperature (T, g) is low, the molecular weight is often large, more than hundreds of thousands. ,Relatively direct, that is, plastic hard, rubber soft (not exactly, there are many exceptions, but most of them are)
- Q: Does antirust oil affect rubber?
- Rust proof oil is a kind of oil which is reddish brown and has anti rust function. It consists of oil soluble corrosion inhibitor, base oil and auxiliary additives. According to the characteristics and application of rust oil sample images can be divided into fingerprint to remove antirust oil, antirust oil, water dilution dilution solvent antirust oil, lubricating oil, seal antirust oil, antirust oil, replacement of thin oil, rust proof grease and rust proof oil. The rust proof oil commonly used inhibitor of fatty acid or naphthenic acid alkaline earth metal salt and naphthenic acid lead, zinc naphthenate, petroleum sulfonate, barium sulfonate, calcium sulfonate, three oleic acid, two tallow amine rosin amine etc..
- Q: How to make mobile phone rubber coat non stick ash?
- Silicone mobile phone sets can not be stained with gray, if not stained with gray, it certainly does not slip ah (such as stainless steel)
- Q: How can I make rubber products brighter?
- Special release agent for rubber products, release agent.Mold release agent is an interface coating used on two surfaces that are easy to adhere to each other. It can make the surface of the material easy to break off, smooth and clean. Mold release agent is used in various molding processes, such as glass fiber reinforced plastics, metal die casting, polyurethane foam and elastomer, injection molding thermoplastic, vacuum foaming sheet and extrusion section. In molding, sometimes other plastics, such as plasticizers, leak to the interface, and then a surface remover is needed to remove it.
- Q: Aging of rubber parts for automobiles
- Due to the comprehensive effect of various internal and external factors, rubber products will deteriorate the chemical properties and mechanical properties of this kind of phenomenon is realized by rubber aging, cracking, sticking, hardening, powder, mold. Shute rubber reminder, especially the rubber parts on the vehicle, due to the complex use of the environment, aging accelerated more obvious.
- Q: What is the lowest cost material for the synthesis of rubber?
- Poly propylene rubber is synthetic materials, he is a kind of synthetic rubber, with ethylene propylene copolymer rubber basic monomer, divided into two EPDM (EPM) and three EPDM (EPDM) two categories;
- Q: Comparison of physical properties of HNBR rubber material with other rubber materials
- Hydrogenated nitrile rubber, referred to as "HNBR" or "H-NBR". It is a new variety of nitrile rubber (NBR).
- Q: Is it necessary to use rubber products for steel structure buildings?
- There must be a rubber cushion for the gear of the crane beam, and there is also a rubber cushion between the crane track and the crane beam. Of course, not all deformation joints are rubber, depending on how to choose the design node.
- Q: What kind of rubber does TPE belong to?
- TPE does not belong to rubber.Although TPE has a tensile resilience similar to that of ordinary rubber, TPE is thermoplastic and rubber is thermosetting. Rubber needs cross-linking. It can not be reprocessed after molding. TPE can be processed repeatedly.
- Q: There is a crack in rubber products
- It is possible that the sulfur is too fast, the outside is ripe and the inside is slow cooked because of the uneven expansion
Send your message to us
Gaskets EPDM Rubber Ring O Ring DN1100 on Sale
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords