FORKLIFT CATEGORY Hand Stacker-- SFHXX16-A
- Ref Price:
-
$8,000.00 - 20,000.00
/ unit
- Loading Port:
- Shanghai
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1 unit/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Hand Stacker Double-Acting Pump It’s design and small turning radius makes it easier to make sharp turns. Controllable direction handle Has a dual pump for easier lifting. Conforms to EN1757-1 Top quality hydraulic pump & cylinder Protection device for steering wheel & safety guard for load roller |
Stackers are used to stack in different patterns, such as cone stacking and chevron stacking. Stacking in a single cone tends to cause size segregation, with coarser material moving out towards the base. In raw cone ply stacking, additional cones are added next to the first cone. In chevron stacking, the stacker travels along the length of the stockpile adding layer upon layer of material.
Stackers and reclaimers were originally manually controlled, with no means of remote control. Modern machines are typically semi-automatic or fully automated, with parameters remotely set. The control system used is typically aprogrammable logic controller, with a human-machine interface for display, connected to a central control system.
Most stackers are electrically powered by way of a trailing cable. There are basically two types of cable trailing: power cord rotating drum (PCRD) and control cable rotating drum (CCRD). Pendulum adjustments are made to ensure the proper alignment of these cables while the stacker is travelling.
- Q: How wide is the internal-combustion forklift pass?
- That depends on the area of the warehouse and the radius of the forklift and the size of the body. The calculation formula for the forklift channel:
- Q: How does the forklift start?
- Why is the front wheel of the forklift narrow.I hope my answer will help you.
- Q: What is the tonnage of a few tons of forklifts?
- Most of the ports are not bad, and they buy a lot of forklifts. There are more than 10 tons of forklifts in the harbor, as well as the container size forklift
- Q: What rules do forklift drivers adhere to?
- First, people without special forklift training and authorization will not be allowed to operate any forklifts, and driving forklifts in the highway will require at least a B driver's license. To operate a forklift in the working area, you must have the driving license issued by the employer's book in person.
- Q: The basics of driving a forklift
- Note the position of the gearshift and the reverse pole. The speed of the forklift truck is slow, usually only one and two blocks, and a reverse gear is specially set up. When driving, first hang in the reverse gear, switch the forklift to move forward or back, then push the shift lever to 1 stop and start smoothly. The forklift does not stop changing direction, causing damage to the transmission.
- Q: The forklift is limited in the factory area
- 5KM/H, the water on a forklift, people go beyond 5KM in an hour. A bit of efficiency is gone. In the case of safety, no matter, the maximum of 20KM/H, the maximum of 15KM/H. This is the top speed of a small tonklift truck.
- Q: What type of rubber forklift tyre
- There are several tons of forklift trucks, and the wheels are on the side of the tyre. Diesel fuel car The front wheels of the 3.5 ton forklift are 28 times 9-15. The rear wheel is 650-10 The front wheels of the 3 ton forklift are 28 * 9-15. The rear wheel is 650-10 The front wheel of the 2.5 ton forklift is 700-12; The rear wheel is 600-9 The front wheel of the three-ton forklift is 700-12; The rear wheel is 600-9 The front wheel of the three-ton forklift is 650-10; The rear wheel is 500-8
- Q: Learn the forklift truck, will you be tired in the future?
- Generally not tired if you usually have a fork in the shelf and you can get a good habit of driving a forklift
- Q: Where to test for a forklift?
- The general exam is to seek the quality board to register, but as you say, ask to provide the data to be more strict If you don't have to do it yourself, it's a lot easier to do it, but I can do it in detail
- Q: The depreciation period and the rate of depreciation of engineering machinery such as forklift truck
- The depreciation of engineering machinery is five years The invoicing price is depreciated according to the actual amount
Send your message to us
FORKLIFT CATEGORY Hand Stacker-- SFHXX16-A
- Ref Price:
-
$8,000.00 - 20,000.00
/ unit
- Loading Port:
- Shanghai
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 unit
- Supply Capability:
- 1 unit/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
