Hand Stacker--SFH1016/1025/1030-A

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

PRODUCT NAME:Hand Stacker--SFH1016/1025/1030-APRODUCT INTRO

Heavy duty design with quality mast constructin.

Drop forged forks.

Straddle leg design suitable for two faces or low pallet.

Light and easy manual steering system.

Model SFH Series

1KG=2.2LB 1INCH=25.4MM

Q: How much is the 8 square meter tatami mat: Wants to see you with what kind of wood, to make what kind of structure, whether or not to do lifting platform, finally, custom matching straw mat, ranging from several thousand to tens of thousands of, I will ask carpenter in my attic made a simple platform of more than 20 cm from the ground to add a row of little cupboard (pictured)

Q: Hydraulic platform repair work instruction book, trouble which big man helps to provide: Remove and disassemble the descending valve, blow the plunger through compressed air and then load and resettle. Remove the hydraulic oil, tighten the connector and remove the oil strainer and clean it with compressed air, then put it back in the tank and connect the line. Do not use old oil for new oil

Q: How do you jump to the wall and jump to the wall?: Press the right mouse button and press the space and direction. You can't go to see the strategy.Don't press the blank, I remember, for a while.

Q: To make a four trapezoid screw lifting up seven tons of lifting platform should be matched with the straight screw and motor: Can be judged according to the accuracy requirement of lead screw grinding or rolling, depending on the load and its acceleration can choose servo power right away and screw the maximum load capacity (do longer engineers can intuitive judgment the diameter of the screw and large), so that you can around the power of the servo motor of the different speed and different lead screw to match, so there will be several different schemes: high speed servo motor with small lead screw (sometimes deceleration machine), big inertia servo with lead screw. Under the condition of the machine cost to determine, from two to three scheme choice, choice of method is to choose low cost, with high stability, cost effectiveness and cost are the same common and suppliers have a spot. If the single from choose the ways of the servo and screw usually have an intuition, like 3000 revolutions of servo goods on the market the most sufficient, screw is according to the supplier's inventory.

Q: What is the price of the hydraulic platform: Price is not uniform, see what you want to do. We are also on the platform, the price has not been raised.

Q: Introduction of vertical elevator milling machine: Vertical knee-type milling machine is a general-purpose milling machine. Vertical milling machine by end milling cutter, end mill, cylindrical milling cutter, saw blade milling cutter, wafer cutter, end milling cutter, and various forming milling cutter for machining various parts.

Q: What happens when the platform comes up and the power goes out.: Many platforms have an emergency drop.I hope my answer will help you.

Q: How to maintain the platform?: Remove the hydraulic oil and remove the oil strainer, remove the oil strainer, clean it up, and then put it back in the tank and connect the pipe. (put on new oil and don't use the old oil. Otherwise, the moving parts of the hydraulic lift system will accelerate the wear and tear.) Remove and disconnect the lift valve, blow the plunger down with compressed air, then load and resettle. Check all hydraulic pipes and connectors. The pipe should not be broken, the joints should not be loose, and all the joints must be tightened.

Q: There are different kinds of milling machine and vertical lifting machine milling machine: Horizontal milling machine also can use the above all kinds of cutting tools, but not as convenient vertical milling, mainly can use the rack cutter (mainly side and face milling cutter, flake cutter, etc.). Milling tank, milling plane, cutting etc

Q: Simple manual lifting mechanism, a nut a bolt can: Handle is fixed below the floor below need not fixed, it is not fixed under the base plate is fixed, the floor below the retaining common shim fix the quotas for marketing or for cap.

Send your message to us

*Email

*TEL

*Quantity

*Unit