Ductile Iron wafer butterfly valves DN430
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 set
- Supply Capability:
- 80000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
A butterfly valve consists of body ,stem ,disc , actuator (manual actuator, worm-gear actuator , aerodynamic actuator or electric actuator) , and wafer type butterfly valve can implement the process for turning on turning off and regulating the flow by the circumrotation of stem and disc that is droved by actuators.
1.Simple and compact construction. Small in size and light in weight. Easy transportation, installation and maintenance.
2. Quick 90 degrees on-off operation. Minimized operating torque ,energy saving.
3. Excellent sealing performance with no leakage. Long service life.
4. Wide selection of materials ,applicable for various media..
5. Flow curve tending to straight line. Excellent regulation performance.
- Q: Does the wet alarm valve group need to install the signal butterfly valve?
- The wet alarm valve group shall be equipped with signal butterfly valve.The signal butterfly valve is generally installed in two parts: floor level, dry pipe, flow indicator front end, trunk pipe, wet alarm valve, front end.Floor level pipe installation is a function of the signal valve, when the floor spraying system needs repair, close the valve, open the end of the floor drain, emptying the water in the spray system, maintenance;
- Q: Classification of telescopic butterfly valve
- (1) Central sealed butterfly valve(2) single eccentric sealed coal valve;(3) double eccentric sealed butterfly valve(4) three eccentric sealed butterfly valve (1) soft sealing butterfly valve.1) the sealing pairs are made of non-metallic soft materials, which are made of non-metallic soft materials.2) the sealing pair is made of metal hard material and is made of non-metallic soft material.(2) metal hard sealing butterfly valve. The sealing pair is made of metal hard material and is made of metal hard material. (1) forced sealing butterfly valve;1) elastic sealing butterfly valve. The pressure of the valve seat, seat, or plate is produced when the seal is closed by the pressure from the valve
- Q: My caravan is a bit sluggish on the pick up, I replaced the wires/plugs and the electronic distributor(I think thats what it is..). still a bit sluggish. Should i look at the valve gasket? Or fuel filter, or fuel pump next? 03 caravan sport 3.3L
- There is no electronic distributor on your caravan it uses a coil pack To the 1st poster there is no valve pan gasket you have valve cover gaskets. The fuel filter on your van is Incorporated in the fuel pump module located inside your fuel tank. There a several things that can contribute to sluggish performance, look at your exhaust and make sure it is not bent/collapsed/restricting Dodge Chrysler Jeep Tech
- Q: Are fire fighting signal valves and signal butterfly valves the same thing?
- The same nature: both can open and close, there is also information back fed.Signal valves are collectively referred to as signal butterfly valves.
- Q: The flow ratio of area and maximum flow area of the valve is? If it refers to the opening of the valve rotation angle? Butterfly linear closure refers to the butterfly valve at constant angular velocity close? When the change trend of flow is what? These valves problem bothering me for a long time,
- Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis rotation, so as to achieve the opening or closing or adjustment; actuators have electric or pneumatic, and so on, through the transmission device to drive the stem, valve plate rotation;
- Q: What does the butterfly valve D361H - 25C DN350 mean?
- Corrigendum: correct type: D361H-25 DN350Should not have C, nominal pressure above 1.6MP carbon steel valve material code name should be omittedValve: central vertical plate welded turbine butterfly valve, nominal pressure 25kg, caliber 350mm, body material, carbon steel, sealing surface material: Cr13 stainless steel
- Q: Butterfly valve network and ordinary butterfly what is the difference?
- Butterfly valve used in the network structure, closed with the more closed, the more tight function, reliable sealing performance, after opening and closing, make sure that the cover is completely out of touch, to ensure that the sealing surface is not damaged. The sealing surface is made of stainless steel, corrosion resistant, high temperature resistant, long service life. With two-way sealing function, medium flow is not affected by the installation restrictions (if only one-way control medium should be used to seal the installation direction) is not affected by the spatial units, can be installed in any direction.
- Q: Butterfly valve sealing material has several?
- Butterfly valve sealing material has nine kinds:X1 (natural food gum);X2 (Heipalen);X3 (ethylene propylene rubber);X4 (chloroprene rubber);X5 (Ding Qing rubber);X6 (abrasion resistant rubber);X7 (fluorine rubber);X8 (silicone rubber);X9 (heat resistant ethylene propylene rubber).Also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control the flow of air, water, steam steam, all kinds of corrosive medium, mud, oil, metals and radioactive liquid media and other types of fluid. On the pipeline, mainly from cutting and throttling. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation.
- Q: Which is more expensive, gate valve or butterfly valve?
- Same diameter, the same material, with the pressure level, the weight of the gate valve is much heavier than the butterfly valve, about 2 times of the butterfly valve!
- Q: When i waa replacing the valves in the las 4 valves , they dropped and i dont know how to make them go back up, and i dont want to take the engine out of the car, is there any tool to make the valve go back up or there is any way to do it?? People told me that i can crank it by and , but i dont know how to do it where do i have to do it, i need help please im begging for help!
- As you've been asking this question for a week now time and time again I guess its time for the Nasty one to set you straight, As I've been a mechanic for over 30 years my knowledge is vast and no further questions need to be asked, You screwed up! now that you have dropped the valves into the cylinders you have to remove the head or heads that you screwed up on, period, end of sentence, there is no other way, and no you will not need to remove the engine to remove the heads, But had you did a bit of research before diving into this without a clue you would have found that a simple length of clothes line or thin rope stuffed down the spark plug hole and turned the engine over by hand to bring the piston up and push the rope into the valves to hold them place would have saved you from pulling the heads off this POS, excuse me I meant fine piece of English engineering, by trying to turn the engine over now is just a good way to bend a valve, and for all you know the piston could have been at the bottom of its stroke and the valves fell out of there guides are not even in contact with the head, so with this said do some research on how to remove the heads on this thing and fix your screw up. Live and learn, you just opted to learn the hard way,
Send your message to us
Ductile Iron wafer butterfly valves DN430
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 set
- Supply Capability:
- 80000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords