High Performance Ceramic Fiber Board with Ceramic Filter Plate

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT OR LC

Min Order Qty:: -

Supply Capability:: -

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Specifications

Low Heat Storage,low thermal conductivity
Excellent compressive strength
Not fragile materials, excellent flexibility

CERAMIC FIBER BOARD

Product Series

1050Ceramic Fiber Board

1260Ceramic Fiber Board

Description

FUJI 1050/1260 Ceramic Fiber Board was processed by the advanced production line.which was adopted the full automatic control and the continuous- processing method.

FUJI 1050/1260 Ceramic Fiber Board have many typical characteristics.such as exact measurement.excellent toughness,excellent heat preservation and can be cut discretionally

The processing work is much advanced.which totally avoid the long production cycle and the low production capacity.

FUJI 1050/1260 Ceramic Fiber Board is divided in different series by the temperature.can be widely used as the back lining of industrial furnace and the hot surface of the low temperature furnace. It is one of the guarantees of reaching the energy conservation and the high quality.

Characteristic

Low Heat Storage,low thermal conductivity

Excellent compressive strength

Not fragile materials, excellent flexibility

Exact measurement,excellent flatness

Homogeneous structure, excellent machine-processed capability

Easily fixing specialty

Processed continuously,the fibers interweave shapely and excellent stability

Excellent chemical stability and thermal shock resistance

Application

Heat preservation and insulation materials as the back lines for the kilns in the field of cement building

Heat preservation materials as the back lines for the kilns in the field of ceramic

Heat preservation materials as the wall lines and back lines for the kilns in the field of metallurgy and petrochemical industry

Heat preservation materials as the wall lines and back lines for the Glass furnace.

Refractory and insulating materials for heat treatment equipment

The back lines of refractory brick for electrolytic reducing bath in aluminum factory

Materials of the wall lines and back lines of heat and pyroreaction equipment

Q: What happens when the pressure on the filter plate is uneven during backwashing?: It should be said that the ceramic filter backwash, usually with a certain pressure of clean water to backwash.

Q: The use of water glass as beneficiation agent, copper concentrate in the ceramic filter can not filter, how to do?: Water glass is a kind of adhesive of flotation reagent, after use may cause the pulp viscosity increased, leading to the adsorption resistance of slurry becomes large, when using ceramic filter filtration dewatering, vacuum suction surface of the microporous ceramic filter plate is smaller than the resistance, there may be a suction effect or even not suction. Some flocculant agents can lead to this phenomenon.

Q: Microporous ceramic filter plate cleaning: For the use of a long time, the method 1, the effect is still no significant improvement, that is how to plug the ceramic filter plate regeneration? The ceramic filter plate with uneven or non sucking slurry can be removed, and oxalic acid or other acid liquid with certain concentration and certain temperature can be taken together to dredge the microporous of the ceramic filter plate. (do not recommend sulphuric acid)

Q: What is the reason that ceramic filter does not absorb mineral powder?: There may be a failure of the filtrate pump, the diaphragm of the pump is damaged, and the mechanical seal of the pump is invalid

Q: How can I avoid the backwash pressure in the production of ceramic filter?: The backwashing system of ceramic filter is usually made up of water inlet, water inlet, pressure gauge, water filter and filtered water pressure gauge, and then connected to the inside of ceramic filter. Such as the discovery of ceramic filter recoil pressure became smaller or even no recoil pressure, you can carefully observe the surface of the ceramic filter plate is wet or ceramic filter plate wear without water injection at the discharge point, investigation and the reasons for the following aspects:Is the water inlet pressure or normal?How about the sealing performance of the water filter? Does the filter element need to be replaced?Is the recoil system piping (metal pipe, ceramic filter plate, connecting pipe, etc.) broken, leaking or dripping?Is the distributor valve properly installed and is it worn?Are there any cracks in the ceramic filter plate?Is the pressure gauge broken?The most likely reason is 1, 2, two, the best water should not be too dirty, filter should be replaced regularly. I hope the answer can help you.

Q: Excuse me, what's the reason that all ceramic filters do not attract ore?: After the joint cleaning, 0~2 hours of suction effect may be good, 2~4 may drop slightly, 4 hours later will become worse and worse, or even suck. This case should first check the backwash water pressure (instantaneous maximum pressure should not be less than 0.08MPa) is to meet the requirements, should also advance down (to ensure normal and ultrasonic cleaning combined with nitric acid dosage sufficient) and prolong the cleaning time.

Q: The vacuum of ceramic filter is not enough: The vacuum degree of ceramic filter is about -0.08MPa, if the ceramic filter is less than 0.06MPa, the vacuum is not enough. If the vacuum of ceramic filter is not enough, it will influence the suction effect of ceramic filter (mainly the thickness of filter cake and water content of filter cake).

Q: Beneficiation ceramic filter no problem, the technical parameters are normal, but filter out the concentrate water suddenly excessive, what is the reason?: The ceramic filter ceramic plate ceramic microporous pumping vacuum adsorption concentrate filtration water, the adsorption parameters according to the angle of rotation, reverse cleaning process, check whether there are loopholes in the exhaust pipe, check the ceramic plate use cycle is too long.

Q: What is the backwashing pressure of the ceramic filter?: The working process of ceramic filter is: suction - drying - unloading - backwash - suction - drying - unloading - backwash...... In circulation, suction, the drying process is to make the slurry liquid by vacuum suction and capillary effect (usually water) through the filter media from the left, the filter cake on the filter medium (the two processes like syringe pumping), and then through the scraper discharge, after unloading, ceramic filter machine is complete a cycle in the absorption slurry, drying process, some fine particles may enter the filter medium or stacked on the surface (a lot of pipeline internal filtration medium ceramic filter plate), these small particles blockage will make the filter medium permeability and filtering effect of the loss from the poor, in order to reduce the possibility of blockage ceramic filter, will enter the backwash (this process is like a water jet injector). Ceramic filter backwash is through the pressure of water, these small particles plug discharge ceramic filter board.

Q: What about the leakage of the ceramic filter static and dynamic sealing points?: When the main shaft is rotated, the filter cake is adsorbed on the surface of the ceramic filter plate and dehydrated by the vacuum generated by the vacuum pump.

Send your message to us

*Email

*TEL

*Quantity

*Unit