Aluminum Silicon Alloys/AlSi12 Alloy/AlSi20/AlSi24/AlSi30/AlSi50/Ingot/Bars
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 m.t.
- Supply Capability:
- 8000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Aluminium alloy Introduction:
Weight:5kg/pc
Length:60cm
Width:10cm
Height:4.5cm
2.Chemical Composition
Alloy | Composition（%） | Form | ||||||||
Si | Fe | Ti | Cu | Mn | Cr | Ni | Impurities | Balance | ||
AlSi12 | 11.5-13.0 | 0.35 | 0.10 | 0.20 | 0.10 | - | - | 0.15 | Al | Ingot |
AlSi20 | 18.0-22.0 | 0.45 | 0.10 | 0.10 | 0.10 | 0.10 | 0.10 | 0.15 | Al | Ingot |
AlSi24 | 22.0-26.0 | 0.45 | 0.10 | 0.20 | 0.35 | 0.10 | 0.20 | 0.15 | Al | Ingot |
AlSi30 | 28.0-32.0 | 0.30 | 0.05 | - | - | - | - | 0.15 | Al | Ingot |
AlSi50 | 47.0-53.0 | 0.30 | 0.05 | - | - | - | - | 0.15 | Al | Ingot |
3.Pictures
5.FAQ
We have organized several common questions for our clients，may help you sincerely：
①How about your company?
A world class manufacturer & supplier of castings forging in carbon steel and Non-frrous alloys，is one of the large-scale professional investment casting production bases in China.
②How to guarantee the quality of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
③How long can we receive the product after purchase?
In the purchase of product within three working days, We will arrange the factory delivery as soon as possible. The pecific time of receiving is related to the state and position of customers.Commonly 7 to 10 working days can be served.
- Q: The bottom of the cooker is leaking. How can it be repaired?
- This approach can usually take some time.Other fixes are unreliable.
- Q: While wearing a mask, a halitus how to not let the glasses?
- The key is that one of the top edges should be closed. The kind of mask used in general hospitals is very good. There is an aluminum thread in the upper edge,
- Q: LV how to solder, seek expert advice, please everybody
- Set the tightness of the wire brakeTightness only need to ensure that the wire will not loose, but not too tight, otherwise it will cause the welding wire to drag and drop. To correct the setting, first the tightness to the minimum, and then put on the welding wire, let it through the drive roller, if in addition to welding wire roller is moving, and other parts have stopped, that is not tight enough. Be careful when handling, because too tight will cause excessive force on the wire. In addition, do not strain the last few laps of the wire when it is out of use; it is usually difficult to loosen because the wire is too hard.
- Q: How to remove the wok of the grease and bottom ash
- The washing powder or clean water into the pot after the first precise use of cloth dipped in water to wipe it again, after a while and then brushed aluminum. Iron pot of the group of imitation aluminum wire (such as electric wire like) eraser, stained with washing powder, water wipe, no oil pollution. Our kitchen has not been cleaned for 5 years, it's dirty, and we have many ways to do it. Finally, we use this method to clean the kitchen. It is as white as new. You can try it,
- Q: How did you disconnect the HD line?
- The general HDMI line consists of two parts, the interface and the wire. HD line is specially developed for high-definition video and audio equipment, so he has put forward higher manufacturing requirements for interface, wire, joint and manufacturing process.
- Q: How to process aluminum wire into 0.1 mm aluminum wire, and the efficiency can not be too low
- For FLMY1, FLMY2, FLMY3, FLMY4, granularity 0.16~0. (6063 aluminum alloy scrap), aluminum wire, aluminum profile scrap, mechanical processing aluminum scrap... Not only product quality is good, and processing cost is low, investment is little, quick effect.
- Q: Where is the PN junction of point contact diode?
- The manufacturing process is like this: as shown in the picture, one end of the fine aluminum wire is attached to the anode lead, and the other end is pressed on the doped n type semiconductor.
- Q: How do you plug the trachoma on the radiator?
- In the water under the premise that Chlamydia at keep dry, remove impurities, can use AB up, buy a box of AB 10 yuan, according to the 1:1, smear on the trachoma, best hill, 20 minutes can be used..
- Q: Microdetector internal tied aluminum wire is then used by the eddy current, electromagnetic damping brake?
- What I'm talking about is permanent magnets.Anyway, there is a rule that aluminum does not produce vortex easily. If you want to use the eddy current to consume energy, you will use iron substance. Iron material is more likely to produce eddy currents.Look at the position, angle of the coil. Some use eddy currents to resist external disturbances.
- Q: When fuse is blown, why not use copper wire and wire instead?
- The melting point of copper wire and wire is too low to withstand the heat produced by electricity
Send your message to us
Aluminum Silicon Alloys/AlSi12 Alloy/AlSi20/AlSi24/AlSi30/AlSi50/Ingot/Bars
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 m.t.
- Supply Capability:
- 8000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
