2014 New Tap Design With Brass Handle And Chrome Plated Brass
- Ref Price:
-
$51.67
/ pcs
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 50 Sets PCS
- Supply Capability:
- 2000Sets Per Month PCS/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Product Name:New Tap Design With Brass Handle And Chrome Plated Brass
Carton Packing Size:45*43*44.5cm
About product:
1.Two handles faucet.
2.Easy to installation and eas to clean.
3.High in quality and low in price.
Carton Packing Size:45*43*44.5cm
About product:
1.Two handles faucet.
2.Easy to installation and eas to clean.
3.High in quality and low in price.
- Q: I removed the faucet assembly from the bathroom sink/basin to replace it with a new one and it's completely yellowed underneath. It's not as bad as it was after I tried to clean it with the rubbing compound I would use on my car but still not gone.I have to get it all cleaned away because the new one is not the same shape at the base as the old one.Anyone here had experience with this and know the best stuff to use?
- Chances are its from the pipe dope or plumbers putty that was used. Treat it like a greasy stain and use some baking soda, some cleaner like Greased Lightening or Blue Wolf. You can also try putting some hydrogen peroxide on it over night and covered with a rag or some plastic if its not granite or marble. Should clean up fine then. Good luck!
- Q: American Standard 3-hole double basin basin faucet how to install
- General is the standard of this faucet is the case
- Q: Which brand is good in basin basin faucet?
- Which brand is good in basin basin faucet?
- Q: I have tried a basin wrench, a socket wrench, an adjustable wrench... I have used heat, I have used WD-40, I have used a hammer and a flat head screwdriver to try and loosed the nut and bolt. I have even tried a hacksaw, but that gets me nowhere quick. I really don't want to have to remove my sink completely to change the faucet. I think Hercules tightened these nuts. Can anyone give me some advice on how to get these nuts off so I can change out the faucets?
- I'd have to assume you're referring to the pot metal hex nuts that hold the faucet assembly down in the sink, or possibly the newer plastic nuts, which can sometimes be so tight that it seems nearly impossible to remove them. If the nuts are metal, I'm sort of with Ed, in that I use a Dremel tool with a cutting wheel attachment to cut the nut. You're probably not going to reuse the faucet assembly so it doesn't matter if you mess up the threads on the bolts or threaded pipes hanging down under the sink. The Dremel tool is small enough to get it up into fairly tight areas and with a little care you can cut the nuts in two and then knock them loose with a small punch and hammer. If the nuts are the plastic ones with the four fins sticking up, I made a tool out a piece of 1" galv. pipe, by cutting a couple of slots in a cross formation on top with a hacksaw, that fits right over the fins and can be turned with either a small screwdriver, (if you drill a hole through the bottom end of the pipe), or with a pair of channel locks, by grabbing on to the pipe itself. Just use safety glasses while working under a sink to protect your eyes.
- Q: I'm changing from a white sink to a SS kitchen sink. The faucet is shiny chrome. The sink has more of a dull brushed finish. Should I get a new faucet or do you think it will look fine? Any answers appreciated, especially if you have done this yourself! :)
- Chrome looks good with any sink. Matte finish hides water mineral spots, but, doesn't look as clean.
- Q: how necessary is a reservoir wrench when installing a new faucet?
- Since there is no such thing, not very important at all. If you mean a basin wrench (such as what is in the provided link), though not *necessary* it can (in some circumstances) make installation much easier. Al
- Q: hey guys, im replacing a kitchen faucet for my mom right now, and Its not one of the ones where it scres in on the two side panels, it has a long threaded neck that attatches to the sink basin, how would I take this out, I tried spinning the faucet to just unscrew the threading but it pivots...
- Faucets that I'm familiar with sit on top of the sink and are bolted down below the sink. You have to loosen nuts under the sink from the threaded water supply lines on the bottom of the faucet unit, then lift the entire unit out from the sink. That leaves holes in the sink. Threaded water supply lines on the bottom of the faucet fit through those holes and water lines from your house's water supply are attached to those. But the handles, neck, the whole shooting match is one unit.
- Q: Xin Si Lai faucet wash basin with a little more on the faucet
- Look at the style, generally more than 150
- Q: will connect to vintage tub basin connected to pump.
- Have a blacksmith create one for you.
- Q: I Just bought a new kohler faucet to replace my old but the hoses on the new ones are short. It has a 3/8 connector and my old one had a 5/8 connector...the old hose is pinched into the shutoff valve tap so i cannot remove it...what can i do to connect the old pipe with the new one...please help....home depot was no help
- You fit a 5/8 reducer down to 3/8th.
We are very popular with consummate skill, advanced workmanship, perfect after sales service in the world. From now on, our company devotes ourselves to enterprise construction and development, market is the guide, management is the basis, science is power.
1. Manufacturer Overview
| Location | Kaiping,Guangdong |
| Year Established | 2004 |
| Annual Output Value | Above RMB5 Million |
| Main Markets | Europe and the United States, Australia |
| Company Certifications |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Guangzhou |
| Export Percentage | |
| No.of Employees in Trade Department | 4 People |
| Language Spoken: | English；Chinese； |
| b) Factory Information | |
| Factory Size: | Above 3000 square meters |
| No. of Production Lines | 2 |
| Contract Manufacturing | OEM Service Offered；Design Service Offered |
| Product Price Range | Average |
Send your message to us
2014 New Tap Design With Brass Handle And Chrome Plated Brass
- Ref Price:
-
$51.67
/ pcs
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 50 Sets PCS
- Supply Capability:
- 2000Sets Per Month PCS/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
