2014 Fashion Design Square Handle Brass Bibcock Tap
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 50 Sets PCS
- Supply Capability:
- 2000Sets Per Month PCS/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Description:
brass body
brass handle
brass cartridge
brass parts
Chrome Plated
Carton Packing Size:45*43*44.5cm
About product:
1.Two handles faucet.
2.Easy to installation and eas to clean.
3.High in quality and low in price.
brass body
brass handle
brass cartridge
brass parts
Chrome Plated
Carton Packing Size:45*43*44.5cm
About product:
1.Two handles faucet.
2.Easy to installation and eas to clean.
3.High in quality and low in price.
- Q: Hi, I recently replaced a washer on my hot water faucet and now when running the hot and cold water to shower etc. both run for a bit of time and then I hear a thunk noise (loud enough to hear above the noise of water running) and the hot water will drop off as if it is turned off. I then turn on more and the water runs with no problem. This is constant every time I use it. Any ideas. I believe my cold water slows down also but cannot be sure. I have two handle faucet with a pull up button (for shower) on spout. Sometimes the water after turning it up will come out of the faucet head alittle as if the water is pushing out where ever it can. Thank you for any help you can give me.
- Sound like you have a bad anti-scald valve. Generally you need to replace the entire tub/shower valve, but some manufactures design theirs with a replaceble anti-scald unit.
- Q: Yes I have all the proper tools, I'm using a basin wrench...I've got the old kitchen faucet disassembled...one retainer nut is off after some effort, but the other won't budge (white plastic style)...I can't get it off and it's the only thing holding me back from getting my new faucet in...this is suppose to be an easy project but it's killing my entire day, please help if you have advice!
- If you are replacing the faucet, just break it off, even from the top. Throw it away. I ended up doing this after messing with the basin wrench for 30 mins. The sink is tough enough to hold up, the faucet components are often chromed plastic, which distort when you use a basin wrench anyhow. Use Teflon tape when you put your new faucet on to avoid this the next time.
- Q: What a huge headache it looks like.The rubber seal on my small bathroom sink faucet is leaking just a little bit (not bad). As I look underneath the sink cabinet, the faucet mechanism is way in the back of the sink basin and very hard to get to. Need plumber and they are super expensive. No way I can do this by myself, I do not have the tools for one.Looks like the whole sink apparatus has to come out to get to the underneath portion of the faucet.How much do you guess this will cost? Just to replace this rubber seal that will probabl cost $1.00.Thanks.
- Most faucettes are designed to be taken apart from the handle. Turn off the water supply There is usually a small cap in the centre of the faucette handle. This can be popped out to ecpose a screw that holds the handle onto the faucette. Remove the screw There is a collar that must be removed with a wrench Unscrew the collar (You may have to turn the faucette while unscrewing the collar) Once the collar is completely unscrewed you should be able to pull the inside of the faucette out with a twisting motion Some fausettes have o-rings, flat washers, cone shaped washers. Take the insides of the faucette to a hardware store or plumbing supply. They can advise what washers/o-rings/packings you require for that faucette. Assemble in reverse.
- Q: i have two problems.1. water is leaking out from the cold faucet. I unscrewed the plastic cover, it looks fine, but i can see the water coming out from the iron thing. I suppose the only solution is the replace the whole thing? but the whole thing seems to be glued to the sink. 2. water is dripping down under the sink around this twisted plastic tube. ( i don't know the proper name for those things.) i can see mineral kind of things accumulating around one black plastic circle kind of thing. i think that this should be an easy fix, what should I buy? should just buy that one thing or replace the whole plastice tube, etc?thanks.
- Unless this faucet is near and dear to your heart, just replace it. Be sure to replace it with a good one, because the cheap plastic ones only seem to last two or three years. Your faucet isn't glued to the countertop, it's just attached via two or three plastic nuts. You have to get directly below the faucet (where the water connections are) and you should see what you need to remove to get the old faucet off. There is a special wrench called a basin wrench that you can use or you can just use some pliers. They can be very tight and hard to remove though since you won't have much room. Be sure you turn the water off before you do any work....
- Q: How to install the basin faucet
- In the faucet installation accessories in the angle valve is very important, we must choose the best is a set of angle valve. And there is a gap between the faucet and the angle valve at the time of installation, it is preferable to use a dedicated extension tube to connect.
- Q: Balcony wash basin basin faucet high
- How high is the outlet? This is based on the style of your choice of faucet and basin style to decide. The stage basin and the basin are not the same, the main is the leading style according to the basin style to buy! The
- Q: What is the general supply of water supply basin? If the installation of the wash basin height of 800
- Wash basin itself has a thickness, less than 200 words, then the water pipe is not straight down on the.
- Q: What is the faucet in the basin?
- Head tied to the lower part of the gap leakage reasons: it is because the gland within the triangular gasket caused by wear. You can loosen the screw to remove the tie head, then remove the gland, and then remove the inside of the gland inside the triangle seal, put on a new one.
- Q: Basin faucet special astringent, how to repair ah?
- To solve this problem must be removed from the faucet, which has two buckle on the tube, is hot and cold water pipes, correct inside, and do not remove the faucet can not solve. Also need to clamp, tube wrench special tools, all those who have done in the unit who are competent, you can ask experienced colleagues to help solve.
- Q: i try to fix it myself.i can't seem to unscrew that white plastic ring, it was really tight. so what should i do now? should i hire a professional?
- If your faucet is leaking out the spigot you're working on the wrong part of the unit. This is a tightening hold down nut that threads up onto the water feed pipe and is most likely corroded or rusted in place so bad that the only way to get it off will be to crack it with a cold chisel and twist it off, or get a Dremel tool with a cutter wheel on it and cut it off that way. Either way, wear safety glasses while removing it as rust particles in the eyeballs are not fun. If the leak was coming from underneath the sink, under the faucet, then yes, you'll need to replace the entire fixture. If you do, when you put it back together and put the new nuts on where this one comes off, put a little vaseline on the threads before you put the nut on, it will make it go on easier and certainly, if you ever have to do this again, it will come off easier.
We are very popular with consummate skill, advanced workmanship, perfect after sales service in the world. From now on, our company devotes ourselves to enterprise construction and development, market is the guide, management is the basis, science is power.
1. Manufacturer Overview
Location | Kaiping,Guangdong |
Year Established | 2004 |
Annual Output Value | Above RMB5 Million |
Main Markets | Europe and the United States, Australia |
Company Certifications |
2. Manufacturer Certificates
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability
a) Trade Capacity | |
Nearest Port | Guangzhou |
Export Percentage | |
No.of Employees in Trade Department | 4 People |
Language Spoken: | English;Chinese; |
b) Factory Information | |
Factory Size: | Above 3000 square meters |
No. of Production Lines | 2 |
Contract Manufacturing | OEM Service Offered;Design Service Offered |
Product Price Range | Average |
Send your message to us
2014 Fashion Design Square Handle Brass Bibcock Tap
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 50 Sets PCS
- Supply Capability:
- 2000Sets Per Month PCS/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches