Tig Welding Rods

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT or LC

Min Order Qty:: -

Supply Capability:: -

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Tin Brass Welding Rods

Brass Brazing Rod HS221/HS222

1 % Silver Brazing Rod

Welding Wire for Adrasive Wear

Removable White Board

Mild Steel Welding Rod AWS E6013 Weding Rods Factory

Welding Wire Factory Hot Selling ER70S-6 Co2 Welding Wire Manufacturer

Welding Electrode E6013 E7018 2.5x300mm, 2.5x350mm

Tig Welding Rods

T-SD-1

For TIG Welding

Reference color:dark blue

APPLICATIONS

For hardening and padding to punching dies, press molds and hard iron metal molds, etc.

TYPICAL CHEMICAL COMPOSITION OF WELDING ROD (%)

C	Si	Mn	Cr	Mo	V
0.38	0.96	0.47	5.37	1.24	0.83

HARDNESS OF WELDED METAL

620-670

DIMENSION OF PRODUCT

Rod diameter (mm)

1.6

3.2

Rod length (mm)

1000

T-SD-11

For TIG Welding

APPLICATIONS

For hardening and padding to punching dies, cold steel shears and hard iron metal molds, etc.

TYPICAL CHEMICAL COMPOSITION OF WELDING ROD (%)

C	Si	Mn	Cr	Mo	V
1.44	0.30	0.33	11.11	0.93	0.26

HARDNESS OF WELDED METAL

620-670

DIMENSION OF PRODUCT

Rod diameter (mm)

1.2

1.6

2.4

3.2

Rod length (mm)

1000

Q: What enterprises use more welding electrodes?: Small businesses and individuals now use more. Two oxygen is used for steel structure transmission. And then the site is OK

Q: What welding rod does 20CrMnTiH use?: 20CrMnTi is steel carburizing, carburizing steel is usually carbon, low carbon steel 0.17%-0.24%. The car with the drive gear is in manufacturing. The hardenability of Shanghai Kai Xin steel to provide picturesCr Mn Ti carbon steel permeability, the higher hardenability, the quenching conditions, with high strength and toughness, especially with high strength and impact toughness of.20CrMnTi steel surface carburizing hardening. Good processability, small deformation, anti fatigue performance is quite good. Use: for gear. Shaft, piston type accessories. For cars, aircraft of various special parts. The characteristics and applicable scope: good performance of carburizing steel, high hardenability, carburizing after quenching with hard and wear-resistant surface and tough heart, has high low-temperature impact toughness, weldability medium, normalizing after the machinability is good. Used to manufacture the important parts, such as gears, gear rings and gear shafts, that bear high speed, medium or heavy load, impact and friction, which are less than 30mm. 18CrMnTi is widely used as a substitute for steel, carburized parts, in the automotive industry for the tractor. Under the high-speed section below 30mm. In heavy load or impact. And the important carburized parts, such as gear shaft. The friction ring gear. The gear shaft. The spindle. Sliding bearing. The crosshead. Claw clutch worm. Etc..Welding technology information network weld8 provides answer J857Cr low-alloy high strength steel welding rodJ857Cr low alloy high strength steel welding rod meets: GB E8515-G: AWS E12015-G: J857Cr is low sodium hydrogen type leather with low alloy and high strengthPreheat 200 before welding and 500-700 (or dark red) after soldering

Q: What is the difference between stainless steel welding wire and electrode?Such as;1, its welding effect or quality?2, how does it affect your body?3, its price and cost profit?The main topic of attention; he influence on the human body, (I once heard that the stainless steel has a great influence on man's reproductive function, welding of stainless steel welding technology do not know now there is no change?): Stainless steel electrode is used for arc welding, and stainless steel welding wire is welded by argon arc welding. The welding rod is expensive, but the direct current welder can be used directly. The workpiece is generally used for welding large workpieces or not of good weld quality. Welding wire is cheap, but argon arc welding machine and argon gas arc welding can be used to weld thin plate easily. The welding seam of argon arc welding is easy to handle and beautiful. The cost is not very good, because the use is different. Argon is inert gas has certain harm to the human body, the sea has radiation, radiation damage to the body, it is best not to do this to work, it is best not to do not married children, if do get time to have children, or easily into strange children,.

Q: What type of welding machine does not use electrode welding machine?: The welding machine without electrode is of the same type, that is, common standard welder.Because the welding machine interface size can be adjusted, you can use a variety of electrodes. Instead of an electrode with a welding machine.The electrode (covered electrode) is a strip of metal gas welding or welding when the filler metal in the joint welding of the workpiece. The electrode material is usually the same as the material of the workpiece.

Q: What is a welding rod?: 1. will be welded to the right side of the steel, two steel reinforcement end of the gap should be 2 ~ 5mm2. 2 sides of the 1 steel bars, the steel bar shall not be less than 70% of the welded steel reinforcementThe weld thickness of the 3. joint welds shall not be less than 0.3 times of the main reinforcement diameter, and the width of the weld shall not be less than 0.8 times of the main reinforcement diameter

Q: T107 purple copper electrode welding with what: Inverter type DC welding machine is recommended. DC reverse short arc welding is adopted.Arc instability of AC welding machine.Silicon rectifier DC welding machine is affected greatly by network voltage fluctuation, reactor is not electronic current control, welding parameters are not accurate enough. Welding quality can not be achieved.

Q: Why can DC welding machine weld any electrode?: Direct current, especially the direct current produced by the inverter DC welding machine, is relative to the power frequency AC welding machine. The arc is stable, the spatter is very small, and the arc is not easy to break. The welding parameters have almost no fluctuation under the influence of input voltage. Three phase welding machine also supports thrust current, hot arc ignition function. It can avoid sticking electrode when arc welding with basic electrode. If there is no frequency exchange of AC, it is difficult to weld slag hole. A metal with a high sensitivity to carbon is not susceptible to cracks in heat sensitive metals.Basic electrode J426 J506 can be AC DC welder dual-use. These two kinds of welding rod contain arc stabilizer. However, from the quality of welding, DC welding machine is much better quality than AC welder.

Q: What kind of welding rod should be used for welding cast steel parts?: Welding is also a University Branch, welding rod and welding process need to match the material of cast steel to weld welding defects such as crack, slag inclusion, etc., and the question cannot be answered

Q: Can the Q345A board be welded with 422 electrodes?What kind of welding is best?Thank you!: Q345A (16Mn) is a low carbon structural steel. The electrodes that match the grade strength are the J50- series (E50--)Non important construction can be welded with J502 (E5003) titanium calcium type acid welding rod. The welding rod is good in welding technology and easy to remove slag. The electrode is cheap and suitable for AC welder and DC welding machine. The disadvantage is that the toughness is inferior to the basic electrode.The most important structures can be welded with J506 (E5016) low hydrogen potassium basic electrode. The electrode is suitable for welding of alternating current welding machines with no-load voltage equal to greater than 70V and load rate equal to greater than 60%. And welding of DC welding machine. The electrode contains arc stabilizer, suitable for AC DC welding machine welding.An important structure, such as a rigid larger member, a pressure vessel. Or other structural parts requiring higher welding. Using J507 (E5015) low hydrogen sodium type basic welding rod welding. The electrode does not contain arc stabilizer. Only AX arc welding generator, ZX5 SCR direct current welding machine, ZX7 inverter type DC welding machine welding. ZXG series silicon rectifier welding machine is affected by the fluctuation of input voltage, so it can not be used.

Q: What welding Q235 and 16 steel, please enlighten Masters: If you do not answer the question, the general carbon steel electrode will do, such as J422, J506, and so on, and so on, what you have on hand;If you need a large amount of business, choose a cheaper one;If you answer the questions on the book, use E40, typically J422.

We design based on shape and the number of commodities. You are invited to sample just how good these are by making the first step and contacting us soon. We have obtained a large market share with our high quality and good faith to service for our customer.

1. Manufacturer Overview

Location
Year Established	1947
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b) Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range