Stretch Wrap Film Pallet Shrink Wrap Polyethylene Super Clear Stretch Film

Stretch Wrap Film Pallet Shrink Wrap Polyethylene Super Clear Stretch Film

Ref Price:

Loading Port:: China main port

Payment Terms:: TT OR LC

Min Order Qty:: 100 roll

Supply Capability:: 1000000 roll/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Best Quality EVA Film

PVB Film Roll For Safety Glass

Bopp Transparent Film & Bopp Metalized Film Industry

Bopp Thermal Lamination Film Glossy& Matt

EVA Film,EVA Thermal Film Low Price

Mylar Lamination Film- 38mm Width Aluminum Foil/Polyethylene

Stretch Wrap Film PE Stretch Plastic Wrap Film For Packaging and Protecting

Stretch Wrap Film Polyethylene Film Casting Clear Lldpe Bundling

Introduction of Stretch Wrap Film

Stretch Wrap Film is made of 100% pure sofe LLDPE raw material.

Application of Stretch Wrap Film

Stretch Wrap Film is available in hand-applied and machine formats for product moisture proof, anti-dust, fastening and protecting etc. Our stretch film are widely used in following fields, such as outer packing of corrugated box or pallet, packing of loose and small products together, packing of bare machine etc.

Advantage of Stretch Wrap Film

Economical and Practical

Excellent extension, fight to impale

Excellent ability of binding

Price: According the size and the order quantity

Packing of Stretch Wrap Film

One 20GP container can be loaded about 10-15tons.

By sea or by air all available.

Size of Stretch Wrap Film

Thickness:20-200um

Width:30-300cm

Length:1500-3000m

Notice: Special products made as per customer requirements.

Pictures of Stretch Wrap Film

Stretch Wrap Film Pallet Shrink Wrap Polyethylene Super Clear Stretch Film

Specification of Stretch Wrap Film

Thickness Range	Tensile Strength	Elongation at Break	Angle Tear Strength	Impact Ability of Pendulum	Tackness	Light Transmission Rate	Frog Density
Micron	Mpa	%	N/mm	J/mm	N/cm	%	%
15-17	37	250500	120	0.14	3	93	2.4
18-20	38	300600	120	0.15	3	92	2.5
21-25	39	300600	120	0.17	3	91	2.6
26-30	40	400650	120	0.19	3	90	2.7
31-35	41	450700	120	0.21	3	90	2.8

Remarks

1. The data above are typical results and subject to change without notice.

2. Tolerance: Weight and Thickness: ±10%; Width: ±3mm;

Length: Cut Roll & Log Roll ±0.3m, Jumbo Roll ±0.5%.

3. The products should be stored at room temperature and kept from wet and heat source.

4. It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, and free of grease and oil.

5. The user should take test and do trial-application on the above products before coming into application so as to witness and ensure suitability for user’s special purpose and technique.

We have organized several common questions for our clients，may help you sincerely：

FAQ

①How about your company？

A world class manufacturer & supplier of castings forging in carbon steel and alloy steel，is one of the large-scale professional investment casting production bases in China,consisting of both casting foundry forging and machining factory. Annually more than 8000 tons Precision casting and forging parts are exported to markets in Europe,America and Japan. OEM casting and forging service available according to customer’s requirements.

②How to guarantee the quality of the products？

We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.

③How long can we receive the product after purchase?

In the purchase of product within three working days, We will arrange the factory delivery as soon as possible. The pecific time of receiving is related to the state and position of customers.Commonly 7 to 10 working days can be served.

Q:What are the composite ways of plastic film?: The coextrusion process is the process of extruding a single resin or a variety of resins and extruding them through several molds to form a film (blown into film or cast into film). This composite does not use adhesives, so the composite film will have no residual solvents.

Q:What are the factors affecting the permeability of plastic film?: Film properties. The permeability of polymer film is related to its structure. The permeability of polar film is larger than that of non-polar film, and the amorphous film is larger than crystalline film. In addition, the permeability coefficients of some polymer films are similar to those of saturated vapor pressure. The permeability coefficient of polyethylene and nylon films is several times higher than that of moisture permeability. This is mainly due to the formation of pores between crystals or grains, which facilitates the flow of liquid water.

Q:Is it good to use PP bag or plastic film?: In fact, the plastic film is not good, because the film is easy to produce electrostatic glue sand and other hard particles (hardness greater than disk) due to careless small scratches on the surface of the film and the surface in close contact to remove the disc, so the theory of paper (shell) bag is better than thin film

Q:How is the blow up ratio of a plastic film calculated? What's its formula?: Well, the draw ratio is the ratio of the annular section area to the cross sectional area of the mandrel between the mandrel and the die. But I don't know the blowing ratio of PE and PO.

Q:What's the packing material for yogurt?: Yogurt packaging mostly for blister and blow molding, material PE, PP based, plastic film mostly BOPP film, carton packaging higher cost, carton packaging basically three layer printing layer, carton and inside a layer of film

Q:How many days can the concrete be taken away from the concrete?: Plastic film maintenance refers to the plastic film Wei cover to separate the concrete and air, the water is not evaporated, cement concrete in the water to complete hydration, has reached condensation, hardening. This method can be directly covered in plastic draft on the surface of concrete, or plastic sprayed on the surface of emulsion concrete, until the emulsion of volatile, with a layer of plastic film on the surface of the concrete, in order to make the concrete component isolated from the air to the concrete moisture evaporation and no hydration complete the function. Spray plastic film maintenance is 28d concrete strength low around 8%, because the film is thin, can not be completely separated, frozen adiabatic effect, so in the summer of this method is to add sunscreen facilities (not less than 24h), or will lead to concrete cracks producing filamentous. Generally speaking, the cost of natural maintenance is low, the effect is good, but the maintenance period is long. In order to shorten the curing period, increase the turnover rate of the template and the utilization rate of the site, it is suitable for heating maintenance in general production of prefabricated components.

Q:What's the thickness of plastic film 5C?: The thickness of the film is 0.5 mm, the plastic film 5C model bubble film is based on high pressure polyethylene as the main raw material, and then add brighteners, openings and other accessories, by 230 degrees or so high temperature extrusion Blister Blister products.

Q:Method for removing stainless steel plastic film: Because of their environmental protection characteristics, many water-soluble films have attracted extensive attention in developed countries all over the world. Abroad are Japan, the United States and France etc. the production and sales of such products, such as the United States W.T.P company, C.C.L.P company, GRENSOL company in France and Japan synthetic chemical company and so on, the user is also some well-known large companies, such as Bayet (Bai Er), Henkel (Henkel), Shell (Shell) etc..

Q:Can the concrete surface be covered with plastic film in winter construction?: The advantage of covering plastic films is that water conservation concrete. The need for this chemical reaction. The plastic film prevents water from evaporating while causing heat dissipation and achieves the effect of heat preservation.

Q:New car tires have a transparent plastic film, will not be a problem car, new tires, or the car is the same when you leave the factory?: Is that the factory, is a tire protection film, I had to buy a Giti tire like that.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range