Stainless Steel Sanitary Fitting Plane End Reducer 28x22mm M Profile 304
- Ref Price:
-
- Loading Port:
- Huangpu
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
WELCOME to visit our stainless steel pipeline products here(^_^)
Press fitting system joins pipe without welding or bolting. The components fit by crimping through the use of a special pressing tool. An O-ring that is inserted in the fitting ends of the pipe ensures a leak-proof connection. Press fitting system is the trend of pipeline industry. It is widely used in cold and hot water supply, heating supply, fire protection, medicinal gas, industrial petroleum pipeline system etc.
For the size, now we have 3 series:
1. Out diameters: 16.0, 20.0, 25.4, 32.0, 40.0, 50.8, 63.5, 76.1, 88.9, 108.0 (GB/T 19228.2-2011)
2. Out diameters: 15.88, 22.22, 28.58, 34.0, 42.7, 48.6, 76.1, 88.9, 101.6 (JIS G3448-1980)
3. Out diameters: 15, 18, 22, 28, 35, 42, 54, 76.1, 88.9, 108 (EN 10312:2002)
Technical information:
-- Material: Stainless steel 304 and 316L available.
-- Max working pressure 1.6MPa (equal to 232 psi), testing water pressure: 2.5MPa (equal to 362.5psi).
-- Working temperature from -20 to 110 degree centigrade (with Chlorinated butyl rubber O ring),
-- Suit medium: Cold water, hot water, compressed air, gas, oil etc
The product features as below:
1, thin wall stainless steel pipe could last for 70 years, it is the same life time with normal buildings.
2, no smell, no rusty.
3, recycle material
4, avoid welding, avoid fire dangerous.
Contact us for more details!
- Q: Beauty stuffClothingSafetyStuff for funanything! :]
- I would write ,lay face down in an old walmart plastic bag ,and fold it over several times,then place it in another walmart bag and tie the handles tight and toss in the garbage can.,,,,,,,,,,,,,,,,
- Q: How to distinguish the type of tubing joint?
- Corresponding to the different pipe fittings, you should have a good look at the mechanical design manual
- Q: Pipe joint thread, said in 2 / 3 / 4 points, what does that mean, how to convert ah?,
- External thread of 1/4, 1/2, 1/8 mark is a thread size code, in inches. Insiders usually used to call thread size, one inch 1/4 inch is equal to 8 points, 2 points, and so on is referred to as.G pipe thread (Guan), 55, 60 degrees is a functional division, commonly known as the tube. The thread is machined from a cylindrical surface.
- Q: Has anybody any problems with their Iridium shields flaking? It seems that the mirrored finish and color are starting to flake off around the bottom edge and the tab you use to flip the shield up with. Ive only had the shield for a few months and have only been really caught in the rain once. I use the Motosport Cleaner and Polish to clean it. Any ideas would be most welcome. Thanks
- The glue will only work for the intended piping system. A shark bite fitting will transition from PEX to CPVC to copper. It is a brass fitting, that pushes on to the end of any of these pipes, and once on, will hold leak free. If you need to remove the fitting, there is a small tool, that when used, will remove the fitting in order to access the system, or to reconnect a different type of pipe. There are now more companies bringing their version of these fittings, that can't be removed. Good luck!
- Q: I am trying to install a new smoke alarm inside a room of my house, but when I attach it to the wires in the ceiling it sets off all of the other smoke alarms in my house until I detach it. Is this supposed to happen (in which case is there a way that I can silence them all at once or do I have to silence each one individually), or what can I do so that this doesn't happen?
- The difference between sch 80 and sch 20 is thickness. On the pipe the outside diameter is the same the wall thickness is what changes same on fittings. So yes they will work the fittings will just be thinner walled tha the pipe. This link will give you pipe dimensions. Good Luck
- Q: Neither side works now. Blanket gone bad?
- While I normally might be able to answer you (my husband is a plumber) he's ill. But I can tell you that if you try Home Depot (ask for someone who works IN the plumbing dept). they are very helpful.
- Q: My fire alarms went off this afternoon and I'm not sure how to turn them off. Some are battery powered and some are hardwired into the house. I pressed the buttons on them, and I tried holding them in for a little while. Do I need to hold down the buttons longer and will this shut them all off at the same time? Thanks.
- Trust me. Leaving fire burning at night is not. Safe.
- Q: Has anyone (other than firefighters) ever been taught how to use fire extinguishers?
- If you've unplugged it and detached the cord, then reconnected the cords and tried it again and it still won't work, it's toast. Electric blankets used to last decades, but most current models have a lifespan that's exactly the length of the warranty. How's that for progress?
- Q: Detailed point. I'd like to add some knowledge about it.
- The ends of the pipe shall be flush. The pipe should be flush in sawing grinding wheel and other tools, and burr cleaning and high pressure air blowing after use.When installing, the coaxiality of pipe and joint body should be kept as far as possible. If the pipe deflection is too large, it will cause sealing failure.The pre assembly force should not be too large. The inner blade of the clamping sleeve is just inserted into the outer wall of the pipe, and the clamping sleeve should not be deformed obviously. When the pipeline connection, and then according to the specified tightening force assembly. The tightening force of the phi 6-10mm card sleeve is 64-115N, Phi 16mmr 259N, Phi 18mm is 450N. If the sleeve is badly deformed at pre assembly, it will lose its sealing effect.(2) prohibit adding sealant and other fillers. In order to obtain better sealing effect, the sealant is coated with sealant, and the sealant is poured into the hydraulic system, causing the hydraulic components, such as damping holes, blocked and so on.(3) when connecting the pipe, the pipe should have enough deformation allowance to avoid the tensile stress of the pipe.(4) when connecting the pipeline, it should be avoided to be subjected to lateral force; the lateral force will cause the seal to be too lax.
- Q: Want to know how many types, and each type is best to bring pictures
- Mechanical design manual fourth volume hydraulic pipe joint that part has detailed introduction and each installation size, and comes with the picture Oh, a glance will understand, hope to adopt Oh!
Send your message to us
Stainless Steel Sanitary Fitting Plane End Reducer 28x22mm M Profile 304
- Ref Price:
-
- Loading Port:
- Huangpu
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
