Silicone Hose for Automotive OEM Red
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 PCS
- Supply Capability:
- 50000 PCS/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Production description :
Products ID/mm
ID/inch
straight hose 6mm-152mm 0.235''-6''
1 meter silicone hose 6mm-152mm 0.235''-6''
2 meter silicone hose 10mm-76mm 0.4''-3''
straight reducer 25mm-152mm 1''-6''
45 degree/ 45 degree reducer silicone hose 19mm-152mm 0.75''-6''
90 degree/ 90 degree reducer silicone hose 8mm-152mm 0.315''-6''
135 degree silicone hose 38mm-102mm 1.5''-4''
180 degree/U shaped silicone hose 25mm-102mm 1''-4''
Performance Silicone hose:
1)Uses: turbine superchargers and coolants
2)Operative temperature: - 40°c to 220°c ( 428F)
3)Pressure: 0.3 to 2Mpa
4)Standard Color: blue and black
5)Size tolerance: ±0.5mm
6)Nomex/Polyester reinforced: 4-ply(5mm wall)
So for the universal products, please advise the item no. and the I.D, Length or Height that you need, therefore the quotation list will be sent to you accordingly. thank you!
- Q: Who knows what the oil ratio in the car tires is?
- Tire parts are composed of different rubber, in order to achieve the purpose of its application.
- Q: What's the use of a black rubber tube under the engine of a moped?
- The exhaust pipe has an air vent and the engine exhaust is drawn out.Exhaust pipe structureHose; plastic support screw; pipe wall with fiber coating; spiral wire: special spiral plastic.
- Q: What kind of equipment do you need to make rubber parts for automobiles?
- The premise is that you must do market research and Prospect analysis. Now auto parts production is a small profit, raw material prices, product prices down, the purchase side to rebate, the production process of waste, as well as tax, land tax and other taxes. If it's a new factory, it's not good to open up the situation.
- Q: What are the patterns of electric tyres?
- The tire grip is mainly realized by the tread and ground contact theory, the slicks grip is the highest, but this concept is only limited to the dry land, as if on a slippery road, due to the slicks do not have drainage, will enable the vehicle to handle, safety.Large areas of rubber block design, to enhance the grip more helpful, this is different from the tire tread design, you can clearly see the difference. Generally speaking, emphasis on the movement of tire rubber block will be used in large area more, so as to improve the vehicle's grip, and to comfort the trend of tire pattern will be broken, the rubber block will also be small.
- Q: What kind of material should be used for the sealing ring of diesel fuel filter, what specific requirements should be made?
- Oil resistant rubber with low coefficient of thermal deformationHigh machining accuracy, good surface finishFor example, currently the best Duffett filter sealing ring, all imported from Japan
- Q: I want to know what's the tape on the car door
- Strip door rubber seal (auto) is mainly used for door fixing, dust-proof and sealing.
- Q: What is the difference between the bottom rubber and the foot pad?
- When it comes to floor sizing, all the chairs should be removed, whether they are hand sewn or shaped, and they will be a whole after they are finally put on the bus.Car mats are not the same, are generally five, and now popular Ottomans are special car, that is to say, in general, it is necessary to shop a layer of glue, and then buy a foot pad shop. Because if you want to dismantle the earth glue, it is necessary to dismantle the seat, inconvenient, and it does not dust, no water absorption. The Ottomans are small in size and easy to disassemble. When the pads are dirty, they can be cleaned as soon as they are taken down, while the pads have a protective effect on the glue or carpet of the car.
- Q: The rubber strip causes the automobile white paint to be yellow, what method can remove?
- Hello, this is the rubber oil migration to paint inside with thinner wipe off, the only way on the sheet metal paint spraying shaving off place can!
- Q: What kind of material is good for heat shrinkable tube of automobile air conditioner?
- Water pipe for car: inner and outer layers are made of three yuan ethylene propylene rubber, and the middle reinforcing layer is made of polyester yarn. Air conditioning tube (R134a): butyl rubber tube with reinforced layer. The outer layer of the hose is covered with holes in the outer layer with a hose needle hole machine to prolong the service life of the pipe. The outer layer of the air conditioner hose is usually protected by bellows, and the hose is usually protected with a sheath (EPDM material)
- Q: What are the tyres made of and what is the manufacturing process?
- Refining process is the process of mixing carbon black, natural / synthetic rubber, oil, additives, accelerators and other raw materials, processing in the mixer, and producing the "glue". All raw materials must be tested before entering the mixer and can be used after being released. The weight of each mixer is about 250 kilograms. Each rubber component used in the tire is of a specific property. The composition of the rubber depends on the performance requirements of the tire. At the same time, the change of the composition of the rubber depends on the needs of the manufacturers and the market. These requirements mainly come from traction, driving performance, road conditions and the requirements of the tires themselves. All glue shall be tested before entering the next process - Preparation of plastic parts, and shall be released before proceeding to the next process.
Send your message to us
Silicone Hose for Automotive OEM Red
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 PCS
- Supply Capability:
- 50000 PCS/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords