SAE 100 R1AT / DIN EN 853 1SN DN16

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Q: How can I connect the gas tank connection hose?: The general is directly inserted into the connector on the line, if loose, can use wire twist, still feel not reliable, can go to the market to buy two hoop, screw on the line.Keep it clean.

Q: What is the method of making large diameter rubber joint?: Method for making large caliber rubber parts:Mold making: external shell, internal steam box, steam, internal core, hydraulic cylinder do support (two years earlier, with Jack) and high strength rubber cord wrapped into the mould, after high-temperature steam curing, eventually forming.

Q: The difference between the rubber pipe and PE pipe: PE is the most basic plastic of polyethylene plastics, plastic bags, plastic film and so on are PE, HDPE is a high crystallinity, non-polar thermoplastic resin. The appearance of the native HDPE is milky white and is somewhat translucent in the narrow cross section.

Q: What's the metal hose for fire fighting?: 1 the metal hose is made of 1Cr18Ni9Ti stainless steel, and has strong corrosion resistance.The 2. hose tube is made of thin wall stainless steel tube. It has strong flexibility, flexibility, strong bending and vibration resistance, and reinforced protection of woven mesh sleeve, so that it has higher bearing capacity.The connection of the ends of the 3. flexible pipes can be made into other connecting ways except the thread and the flange standard, so that the connection and the use are convenient.4. the product is not only suitable for mating with rotating joint, but also widely used in soft connection of many kinds of fluid medium transportation.

Q: What does the letter of the high-pressure tubing connector mean?: Purpose: high pressure tubing tubing steel wire spiral reinforced layer and wear resistant synthetic rubber composition used for conveying high pressure, engineering machinery hydraulic oil, gas, petroleum, submarine irrigation, steel mills, chemical plants and other media.

Q: How to determine the tensile strength of GB rubber joint?: The cutting of sample can be done by punching machine. When punching sample, the following points should be paid attention to.The cutting force is uniform, not too large, and with mild soap and water and clean tap water wet specimens (or tools), if a sample cut down, it should be abandoned, not to repeat the old mark for cutting.The direction of specimen cutting should be consistent with the direction of tension and the direction of rolling.

Q: Hose connector JB1885-77 what is the standard?: The reason of high pressure hose joint leakage are the following: "a" ring aging or deformation caused by leakage; the "C" ring assembly is not in place, the two plane connection or "C" uneven pressure ring is cut caused by leakage; "a" ring without compaction, the elastic deformation caused by leakage; the "C" ring spigot groove deep caused leakage. In this regard, the need to re select the same diameter and thick section "C" ring, can also be provided with a sealing plane rabbet groove of cutting or grinding, in order to reduce the rabbet groove depth, the "C" ring has enough elastic deformation (compression should be between 0.35-0.65mm).

Q: What is negative pressure rubber shock proof joint? Is vacuum piping available?: With high pressure, good elasticity, large displacement, balance pipe deviation, absorbing vibration and noise reduction effect, convenient installation, but also can greatly reduce the noise and vibration of the pipeline system, which can solve all kinds of line interface displacement fundamentally, axial expansion and concentricity problems, mainly installed in the pump inlet the vacuum pump inlet, or large, can solve the 100% rubber joint suction flat phenomenon.

Q: Is the installation of submersible pumps mandatory for the installation of flexible rubber joints?: Deep well submersible pump must be equipped with steel pipe, water pipe.Submersible submersible pump, such as submersible sewage pump, according to the use of requirements, consider whether to install the flange connection form, Song River rubber soft joint, so it is not necessary.

Q: What is the high and low pressure circuit of diesel engine?: High pressure oil from the pump to the diesel engine combustion chamber nozzle before that, due to the movement of the piston engine in the process of pressurized environment into the combustion chamber of diesel oil injection so the pressure is high, the combustion chamber is higher than the minimum compression pressure environment stroke made, otherwise the oil can not be sprayed into the combustion chamber. So this section of the road is made of metal.

Send your message to us

*Email

*TEL

*Quantity

*Unit