Pvc Pipe Extrusion Manufacture 50mm-200mm
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 30 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Product introduction
Extruder/Screw And Barrel for Extruder/Plastic Extrusion
Screw Diameter 55 to 65mm
30 to 100 KG/HR
AC20 to 40HP/11.5 to 15KW
Characteristic
Pipe range | 20-63mm single | 20-63mm dual | 75-160mm | 110-315mm | 315-630mm |
Extruder | CMAX51/105 | CMAX65/132 | CMAX80/156 | CMAX80/156 | CMAX92/188 |
Extruder power | 18.5kw | 37kw | 37kw | 55kw | 110kw |
Extrusion capacity | 120kg/h | 250kg/h | 250kg/h | 360kg/h | 800kg/h |
Max. Production speed | 12m/min | 10m/min | 6 m/min | 3 m/min | 1.2m/min |
Process flow
PVC powder + additive --- mixing---feeder---twin screw extruder---mould and calibrator---vacuum forming machine---haul-off machine---cutting machine---discharge rack(or belling machine)
Application
PVC pipe is mainly used in the agricultural water supply and drainage, water supply and drainage construction, cable supporting, thickness of pvc plastic pipe, The lines have conical twin-screw extruder, vacuum calibration tank, haul-off machine, cutting machine, stacker or belling machine and so on. Haul-off machine have two caterpillar, three caterpillar, and four caterpillar, six caterpillar, the cutter use knife-raised cutter or planetary cutter which support chamferring function. And the stacker take into account length, production line is reliable performance, and high quality, we have exported to Egypt, Brazil, Syria, Uzbekistan etc.
Features
1) Main machine uses PVC twin screw, and notch feeder with powerful water
cover cooler, which has greatly improved transmitting capability and ensured
extruding.
2) Adopting double pipe extrusion method, it can greatly increase productivity.
3) Adopting high efficiency double-cavity vacuum calibrating technology and spray-paint
cooler gullet, which improve the finished product passing rate, and meet
the requirements of high speed manufacturing. Vacuum calibrating platform and cooler
gullet are all made of stainless steel
4) Adopting multi-caterpillar haul-off, through the central motor to run all the caterpillar
to reach same height, and ensure roundness of pipes
5) Adopting fully automatic control system with high precision, reliable operation,
easy and convenient handling
6) Suitable pipe diameter: 20 - 630mm
System configuration:
(a) Feeding machine
(b) Conical twin-screw extruder
(c) Mould
(d) Vacuum calibrating tank
(e) Hauling off machine
(f) Printing machine
(g) Pipe cutting machine
(h) Pipe pile-up frame
(i) Auxiliary machine such as mixer, water chiller, belling machine and crushing machine.
Product show
Our machine types:
1. Co-Rotating Parallel Twin Screw Pelletizing Extruders
2. Single Screw Pelletizing Extruders
3. Die Face Cut (Air Cooling) Pelletizing Extruders
4. Double Stage / Double Degassing Recycling Extruders
5. Crushers, Mixers, Storage Tanks, Vibrators, Granulators, Blowers
6. Extruder spare parts
FAQ
PVC sheet extrusion
*Q: What’s the price of this machine please?
*A: Dear customer, for each kind of our machines, we have lots of models.
Generally speaking, we design the production lines according to
different requirements of different machines from different customers.
Therefore, the prices are different. So please kindly inform us your requirements.
For example, the raw material, the output product size, capacity and etc.
The more detailed, the better. Our Engineers will design a suitable production line for you.
- Q: Wire and cable extrusion machine temperature exceeds the process documentation, what are the reasons?
- The temperature tolerance of the process file is too lowChanges in the formula of plastics lead to changes in processing temperatureThe workshop operator failed to execute the document
- Q: Why will the extruder frequency shift stop?
- Because the frequency converter is out of order, you can look at the fault record parameters of the inverter.
- Q: Plastic double screw extruder, pumping air will accumulate material, how is it going on?
- Adjust the assembly and check the exhaust block
- Q: the machine vibration is great, the motor, reducer are checked, no problem, there is abnormal sound.
- Pay attention to the ground anchor.It is better to fasten the joint of the equipment itself.Is the fitting of the moving parts normal?.Is there an impact on the extrusion chamber?.
- Q: Comparison of injection molding machines and Extruders
- Considerations for extruder use:1, extrusion machine is running forward, avoid reverse2, avoid fasting operation, must heat engine feeding operation, so that can avoid sticking bar (holding shaft) phenomenon3, the extruder inlet, vent hole is strictly prohibited access to iron and other miscellaneous, so as not to cause accidents, affect production4, safe use of electricity, grounding wire5. When the machine is running, it is forbidden to touch the rotating parts such as the material inlet, the material outlet, the belt, the gear and so on6, before using the machine should be injected with lubricating oil, so as not to cause damage to the machineSince the extruder as one of the three synthetic plastic material since the advent of rapid development.
- Q: Why? What is the raw material of plastics? What is the process flow of the process?.
- 1. injection molding2., the structure is relatively complex, high appearance requirements. Extrusion does not meet requirements3. most are: ABS, ABS+PC, PP and so on4., according to color requirements granulation - drying particles - filling the mold ---- debugging injection molding machine ---- injection molding production - after the selection of finished packaging (if silk screen requirements, but also the need for silk screen)
- Q: There is a 90 extrusion machine, used in the production of communication cables (outside the cable core is extruded with a layer of LLDPE), now is the configuration of Y2-280M-490KW167A inverter type ACS510197A + ABB), General Motors now found low speed when the current is too large, what reason? How to solve? The details are as follows: used for communication cable production HYA30*2*0.4, 1, line speed is 50 m / min, inverter display frequency 35.3HZ current: 116A; 2, line speed is 40 m / min, inverter display frequency of 28.2hz, current: 140A3, line speed is 35 m / min, the frequency converter significantly method: 157A 24.6HZ frequency current, because the product variety and technical reasons, we need to be in the frequency of 10HZ production. Now, it seems that if I reduce the speed again, the current will probably exceed the rated current. What should I do? Is the motor changed to frequency conversion motor? Or inverter? How to solve? Please heroes pointing, thank you!
- The extruder is a constant torque load. The original configuration is usually a DC governor + DC motor. When using a DC motor, the current is usually constant during the speed rise.
- Q: How to adjust the 65 screw gap in the extruder?
- This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.
- Q: The working principle of an extruder
- The material is moved forward by the extrusion of the screw and the barrel, and the material is fully homogeneous and plasticized in the process of material advance. Then the material is extruded by a certain shape of the die by the die of the die.
- Q: How many roots are produced in an hour for an PVC tube extruder?
- It depends on the type of your extruder and the specification of the tube you produced
Send your message to us
Pvc Pipe Extrusion Manufacture 50mm-200mm
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 30 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
