Plastic Tubes PVC Pipe ISO9001 Wall Thickness 1.6mm-26.7mm Specification 16-630mm Length 5.8/11.8m Standard GB
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 m
- Supply Capability:
- 9999 m/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Specifications
pvc pipe for water drainage
1)Specification of pvc pipe:40mm-400mm
2)Thickness of pvc pipe:1.2mm-7.0mm
3)ISO certified.
2.Properties of pvc pipes:
1) Material: pvc pipe unplasticized polyvinyl chloride
2) Standard: GB, ISO9001, ISO14001
3) Color: white pvc pipe, grey pvc pipe , etc.
4) Specific Gravity, g/cm3, 20(C): 1.35 - 1.55
5) Vicat Softening Temperature, (C) >=79
6) Longitudinal Reversion, %, 150(C) <=5
7) Dichloromethane Resistance Test: No attack
8) Falling Weight Impact Test, TIR, %, 0(C) <=10
9) Tensile Yield Strength, Mpa >=40
10) Fitness of Water Tightness Test: No Leakage
11) Fitness of Air Tightness Test: No Leakage
3.Features of pvc pipes :
1) Light weight, easy to load and unload: PVC pipe is very light, convenient to handle loading unloading, and installing.
2) Good chemicals and drugs resistance: PVC pipe has its excellent resistance to the erosion caused by acids and alkalines, a great help to the chemical industries.
3) Small resistance to fluidity: The smooth surface reduces resistance to the fluids. Its roughness coefficient is only 0.009, much less than other pipes, Under same discharges, smaller cabibre of the pipe can be uesd.
4) Strong mechanical strength: Good resistance to water pressure, outside impact and pressure, is satisfied under any conditions.
5) Good electrical insulation: excellent insulation nature against electricity. the pvc pipe can be served as conduits and pipes in construction cable and wire.
6) Water quality unaffected: The solution tests on the PVC pipe show no affect on water quality when the water flows through is. It is considered the best piping material for running water works.
7) Simple installation: Very easy to connect, thus much time and laborcost may be saved.
4.Application of pvc pipes:
1) Structure Engineering, home water supply and drainage
2) Water drainage/supply system
3) for Agriculture Irrigation, aquaculture
5.Specifications of the pvc pipe:
Outer Diameter (mm) | Wall thickness(mm) | ||||||||
2.5MPA | 2.0MPA | 1.6MPA | 1.25MPA | 1.0MPA | 0.8MPA | 0.63MPA | |||
φ20 | 20*2.3 | 20*2.0 | |||||||
φ25 | 25*2.8 | 25*2.3 | 25*2.0 | ||||||
Φ32 | 32*3.6 | 32*2.9 | 32*2.4 | 32*2.0 | |||||
Φ40 | 40*4.5 | 40*3.7 | 40*3.0 | 40*2.4 | 40*2.0 | ||||
Φ50 | 50*5.6 | 50*4.6 | 50*3.7 | 50*3.0 | 50*2.4 | 50*2.0 | |||
Φ63 | 63*7.1 | 63*5.8 | 63*4.7 | 63*3.8 | 63*3.0 | 63*2.5 | 63*2.0 | ||
Φ75 | 75*8.4 | 75*6.9 | 75*5.6 | 75*4.5 | 75*3.6 | 75*2.9 | 75*2.3 | ||
Φ90 | 90*10.1 | 90*8.2 | 90*6.7 | 90*5.4 | 90*4.3 | 90*3.5 | 90*2.8 | ||
Φ110 | 110*10.0 | 110*8.1 | 110*6.6 | 110*5.3 | 110*4.2 | 110*3.4 | 110*2.7 | ||
Φ125 | 125*11.4 | 125*9.2 | 125*7.4 | 125*6.0 | 125*4.8 | 125*3.9 | 125*3.1 | ||
Φ140 | 140*12.7 | 140*10.3 | 140*8.3 | 140*6.7 | 140*5.4 | 140*4.3 | 140*3.5 | ||
Φ160 | 160*14.6 | 160*11.8 | 160*9.5 | 160*7.7 | 160*6.2 | 160*4.9 | 160*4.0 | ||
Φ180 | 180*16.4 | 180*13.3 | 180*10.7 | 180*8.6 | 180*6.9 | 180*5.5 | 180*4.4 | ||
Φ200 | 200*18.2 | 200*14.7 | 200*11.9 | 200*9.6 | 200*7.7 | 200*6.2 | 200*4.9 | ||
Φ250 | 250*11.9 | 250*9.6 | 250*7.7 | 250*6.2 | |||||
Φ315 | 315*15.0 | 315*12.1 | 315*9.7 | 315*7.7 | |||||
Φ400 | 400*19.6 | 400*15.3 | 400*12.3 | 400*9.8 | |||||
6.FAQ
Q:What is you MOQ?
A:As customer’s request.
Q:What is the production ability? or delivery time?
A:Our production ability support 40HQ order finish in one week.
Q:What is the regular shipping port?
A:Tianjin or Shanghai.
Q:What is your payment?
A:TT or CC.
Q:Can we have sample?
A:Sample free, freight cost you.
Q:For urgently doubts,who online?
A:Sales and marketing Manager 24hours online service.
- Q: What are the different closure options for plastic tubes?
- The different closure options for plastic tubes include screw caps, flip-top caps, snap-on caps, and squeeze caps.
- Q: I still have the fork tubes mounted to the bike. I have removed the cap, spacer tube, washer, spring, damper bolt (from the bottom of the tube) and removed the damper and short spring. I have pried the dust cap (rubber seal) and slid it all the way up. There is a piece of plastic? or nylon? that is blocking the circlip(I assume). I do not have a manual for this bike but I can not get one for a few days, so the help would be great!!
- Just pry the plastic ring up (nothing is holding it). Perhaps it's stuck to the foam ring underneath it. After you remove the circlip, the the fork tube and lower will have to be pulled apart. The fork seal is in very tight. Hold the tube in one hand and the lower in the other hand. Push the forks together. Yank them apart with force (a bushing inside of the forks will hit against the seal like a slide hammer). They won't come apart in one pull. Push them - in - OUT -in - OUT - in - OUT
- Q: Can plastic tubes be reused?
- Yes, plastic tubes can be reused depending on their condition and purpose. If they are clean and undamaged, they can be washed and used again for various applications such as packaging, storage, or transportation. However, it is important to consider the type of plastic and any specific regulations or guidelines for reuse to ensure safety and effectiveness.
- Q: How do you prevent plastic tubes from cracking?
- To prevent plastic tubes from cracking, it is important to handle them with care and avoid applying excessive force or pressure. Additionally, storing the tubes in a cool and dry environment can help minimize the risk of cracking. Using appropriate fittings and connectors that are designed to handle the specific type of plastic material can also contribute to preventing cracks.
- Q: One charged plastic ball is vertically above another in a test tube. The balls are in equilibrium a distance d apart. If the charge on each ball is doubled, the distance between the balls in the test tube would become:a. 4db. 2dc. 8d
- Equilibrium is established when the electric force between the balls = weight of upper ball .. this force is constant at any spacing. F = k.q1.q2 / d? .. .. For constant F .. q1.q2 ∝ d? .. .. d ∝ √(q1.q2) When q1 and q2 double .. (q1.q2) increases by a factor of 4 .. and d by a factor √4 = 2 Ans .. ?(b).2d
- Q: What is the maximum load plastic tubes can bear?
- The maximum load that plastic tubes can bear varies depending on the type of plastic used, the dimensions of the tube, and the specific application. It is generally recommended to consult the manufacturer's specifications or conduct load testing to determine the maximum load capacity of plastic tubes for a particular situation.
- Q: How do plastic tubes compare to polypropylene tubes in terms of chemical resistance?
- Polypropylene tubes generally have better chemical resistance than plastic tubes. Polypropylene is highly resistant to a wide range of chemicals, including acids, alkalis, and organic solvents. Plastic tubes, on the other hand, can be made from various materials such as PVC or polyethylene, which may not offer the same level of chemical resistance as polypropylene. Therefore, when it comes to chemical resistance, polypropylene tubes are usually the better choice.
- Q: Do plastic tubes have any odor or taste?
- Yes, plastic tubes can have a slight odor or taste, especially if they are made from low-quality plastics or have been exposed to certain chemicals. However, high-quality plastic tubes that are specifically designed for food or medical use are usually odorless and tasteless.
- Q: Can plastic tubes be used for storing personal hygiene products?
- Yes, plastic tubes can be used for storing personal hygiene products. Plastic tubes are often used for packaging various personal care items such as toothpaste, lotions, creams, and gels. They are convenient, lightweight, and provide airtight packaging to preserve the contents and prevent contamination.
- Q: How can the PPR pipe be connected with the metal tube?
- The transition piece is a combination of plastic and metal, and the two materials are processed by injection molding process, and the anti leakage sealing is realized through the internal structure without adding other adhesive materials.
Send your message to us
Plastic Tubes PVC Pipe ISO9001 Wall Thickness 1.6mm-26.7mm Specification 16-630mm Length 5.8/11.8m Standard GB
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 m
- Supply Capability:
- 9999 m/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
