Outdoor Full Color LED Module For Advertising CMAX-M7

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.Successful p3.33 outdoor led dispay module
2. Made of P13.33 DIP546 RGB 3in1 module
3. Big viewing angle, high brightnes

Product Description

P13.33 DIP546 RGB 3in1 full color outdoor display
Item	Module Technical parameters
pixel pitch	13.33mm
Display Resolution	24*12
pixel composing	1R1G1B 3in1
pixel density	5625dots/m2
driving mode	1/3 scan constant current
module size	320x160cm
grey grade	16384(14Bits)
brightness of white balance	6500Nits
viewing angle	H:100°/V:50°
best viewing distance	12m
encapsulation of led	DIP546
led parameter	R:625-630mm;G:525-530mm;B:470-475mm
operating power source	DC 5V
consumption	20W(30W)
Working environment temperature	-20° ~ 60°
Frame material	black PC
lifespan	100000H
Module weight	700g

Outdoor Full Color LED Module For Advertising CMAX-M7

Q: LED display power can not be displayed properly: In the process of using the control system, the occasional LED display will encounter a black screen phenomenon. The same phenomenon may be caused by a variety of different reasons, even the process of blacking the screen will be due to different operations or because of different environments vary. For example, it may be a power of the moment is black, it may be black during the loading process, it may be black after the completion of the transmission and so on.

Q: What is the difference between an LED display and an LCD monitor?: Notebook LCD screen commonly used is TFT. TFT (Thin Film Transistor) refers to the thin film transistor, each of the liquid crystal pixels are integrated in the pixel behind the thin film transistor to drive, which can be high speed, high brightness, high contrast display screen information is the best One of the LCD color display devices is now the mainstream display device on laptops and desktops.

Q: Is the TV screen good for the LCD or the LCD?: In contrast, LED can easily do the regional regulation (which can be a certain degree of LCD light leakage problems, but can only be mitigated, theoretically almost impossible to achieve the traditional CRT CRT TV contrast), and life Longer (CCFL tube work for a few years there will be a decline in brightness or start the difficult phenomenon, need to be replaced.

Q: What is the thickness of the led display?: The thickness of less than 75mm, with the aluminum. Can also be thinner but the material is not easy to find.

Q: LED display power supply how to configure how many units with the plate is calculated.: According to the unit board power calculation, P10 monochrome in general 10 to 12 blocks, indoor monochrome 12, indoor color 6, full color, then ask the unit board manufacturers, a board of how much power. And then calculate their own bar.

Q: LED display a board dark light how is it?: With a multimeter to measure whether the normal voltage of the unit board, and then measure the power module voltage output is normal, if not, then determine the power module bad.

Q: LED electronic display and P have anything to do: For outdoor led display, from the near, the general use of P10 or P12, a little bit with the P16 or P20, and for indoor display, the general P4 ~ P6 can be, a little bit to use P7.62 or P10.

Q: Led display brightness is not enough because of what are the reasons: If the screen is a very small piece of time is sometimes very dark, the unit is usually a problem, or drive IC problems, to replace. If the entire LED screen has become very dark, if the circuit board control system problems, it is recommended to restore the factory mode. If it is caused by the graphics driver, it is recommended to update or reinstall the driver.

Q: IPS screen and LED screen difference: LED is the light-emitting diode, so the so-called LED screen is the concept of confusion, in fact, LCD panel with LED as a backlight, but also useful as a backlight CCFL, CCFL is cold cathode fluorescent tube,

Q: Led display speed how to tune: When installing the LED bar screen software, enter the text that needs to be displayed in the blue edit box. After the text editing is finished, click "Frame Properties" to pop up the following dialog box to set the frame properties. Display speed 1 fastest, 16 slowest. After setting the current frame, you can point to "previous frame" or "next frame" to move to another frame. After all the parameters of the frame are set, click the "Exit" button to return to the main window.

Send your message to us

*Email

*TEL

*Quantity

*Unit