P10 Outdoor Red Color LED Display CMAX-P10
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- -
- Supply Capability:
- 10000000 M2 Per Month m²/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Specifications
Ultra bright led message display
Easy-to-use
PC control with 2 years warranty
Multi-language selectable
Aluminum frame
48X256 pixels outdoor red led moving message sign
Display size: 480X2560mm
Case size: 480X2560mm
Pitch: 10mm
Resolution: 48X256 pixels
Whole screen resolution: 12,288 pixels
Display color: red
Pixel composition: 1R per pixel
LED type: DIP546
Cabinet: iron, waterproof
Driver mode: 1/4 scan
Communication way: network port to communicate with PC
Include meanwell power supply, control system and wooden packaging
It can display text, number, graphics, time, temperature etc.
- Q: LED display power can not be displayed properly
- Make sure that all hardware, including the control system, is fully powered up. (+ 5V, do not reverse, then wrong)
- Q: What is the difference between an LED display and an LCD monitor?
- Notebook LCD screen commonly used is TFT. TFT (Thin Film Transistor) refers to the thin film transistor, each of the liquid crystal pixels are integrated in the pixel behind the thin film transistor to drive, which can be high speed, high brightness, high contrast display screen information is the best One of the LCD color display devices is now the mainstream display device on laptops and desktops.
- Q: 16: 9LED What is the approximate size of the display?
- 16: 9 is only a proportional form, the specific size to be determined according to the area of the display. You display 16 meters long, 9 meters high, is 16: 9 ratio; display length of 10 meters, 5.6 meters high, is also the ratio of 16: 9. So there is no specific size!
- Q: LED display power supply how to configure how many units with the plate is calculated.
- According to the unit board power calculation, P10 monochrome in general 10 to 12 blocks, indoor monochrome 12, indoor color 6, full color, then ask the unit board manufacturers, a board of how much power. And then calculate their own bar.
- Q: How to identify the quality of led display quality
- Led display driver IC: the current development of led display driver is a bit crystal, Mingwei, and some domestic drive IC;
- Q: How do I choose the dot pitch of the LED display?
- LED display: LED light: according to the color of the lamp is divided into red, green and blue three primary colors; unit board, module; according to the pixel spacing is divided into ph10, ph16, ph20, ph40 and other series, the minimum point spacing 5mm, maximum 50mm;
- Q: LED electronic display and P have anything to do
- P generally represents the pixel pitch, and P followed by the value of the two mainly refers to the distance between the pixels, usually called the point spacing. And the smaller the value of this point spacing, the higher the unit pixel, the more clear the display screen.
- Q: LED display more than the size of the area must be 380v
- LED display itself only need low-voltage DC power supply, whether it is 380V or 220V need to go through the buck and rectifier, which is the screen does not matter. Whether it is to use 380V or 220V depends entirely on the load balance of the power grid considerations, which depends not only on the size of the display, but also on the local grid capacity. In general, LED is weak devices, even if the display area and then large, the total power is also less than where to go, so you can use 220V single-phase power supply, but the power supply cable cross-sectional area to be larger, but the power circuit Much simpler.
- Q: Led display brightness is not enough because of what are the reasons
- Note: The above is the common cause of the LED screen dark screen, starting from the basic situation, one by one investigation, if the above can not solve your problem, please contact the warranty.
- Q: Led display point density is what it means
- LED display density refers to the LED display per square display the number of pixels, such as P10 model LED display is 10,000 pixels per square point, P16 model refers to the display refers to 3906 pixels per square point.
Send your message to us
P10 Outdoor Red Color LED Display CMAX-P10
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- -
- Supply Capability:
- 10000000 M2 Per Month m²/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
