Off-road scissor platform

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Off-road scissor platform

Q: How does the table in the middle of the tatami mat go up and down: Base installation: the lifting platform will be raised slowly (no shift in the lifting procedure). Attach the top of the platform to the tatami mat. To make sure the position can be locked first two screws, then drop the platform to make sure the position is not running, if there is any running bias correction.

Q: When the hydraulic platform drops, it feels very shaken and unbalanced. Please answer?: Connected to the solenoid valve is the control valve core, if it is to be repaired. To change oil, you need to lift it up to the top, and then use the safety support frame or stick to support it so that you can do what you want

Q: Does the shear fork lift stand belong to special equipment?: Agree to this answer, at the rated weight is less than 0.5 t, no license. In the light of the special equipment safety supervision regulations, hoisting machinery definition: refers to used for vertical lifting or vertical and horizontal moving heavy mechanical and electrical equipment, its range is rated lifting weight greater than or equal to 0.5 t lift. According to the "special equipment catalogue", it should be the type of crane/elevator/elevator platform (the premise is greater than or equal 0.5 t).

Q: What certificate is required to operate hydraulic platform: Need special equipment to use the license, do this card is very expensive, seem to want 500 ~ 10000. Where did you buy it, because the house can do it for you? If the product does not meet technical review do not water,,,, I know there is a producers can do STH for sb, HuaNanJun industry machinery equipment co., LTD, special equipment to check more strictly, now,

Q: How is the lifting handle of the universal knee-milling machine very tight: There are a lot of problems with that. It depends on the circumstances. If it's an old machine, it won't be easy to judge. New machine tools are different,

Q: What is the hydraulic platform driven: Choose an electric motor or internal combustion engine based on load and situation

Q: The hydraulic platform can't rise. Why?: The hydraulic platform and the control line are relatively simple, the hydraulic pump running at the point of rise will drive the oil hydraulic drive plunger up. Turn on the solenoid valve when the point is lowered. Be described in the hydraulic pump caused by dirt Chen Ji which reduces the pump fluid efficiency, hydraulic pump will be removed to clean the pump tablet, does not rule out the filtrate may be network jam.

Q: How to use the elevator to be safer and more efficient: Annual maintenance Check all hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. Remove the hydraulic oil, remove the oil strainer and remove the oil strainer, clean it up and then put it back in the tank. Be familiar with 'ten notices' 1, pay attention to the agencies should regularly check and adjust the brake of the brake and the clearance between the brake wheel, flexible and reliable. The clean surface, there should be no dirt, in case of dirt must wash with gasoline or thinners. 2, pay attention to removing the hydraulic tank of fuel cap, remove the cap around earth, unscrew the cap, remove residual impurities in the joint area (not rinse in order to avoid water seeping into the tank), confirmed to open the cap. 3, pay attention to the elevator remove the hydraulic tank of fuel cap, filter cover, test hole, hydraulic tubing parts, cause the system oil when exposed to avoid dust, remove the parts to open completely clear before first.

Q: How to maintain the platform?: My company has, our brand: niu power Throughout guangdong, there are 57 dealers across the country. Check it online, it's ok to buy it, but at least it will give you advice and contrast!

Q: Safety operation of hydraulic platform: Purpose: this procedure is used to guide operators to operate correctly and use hydraulic platform equipment. Two procedures: 1, the parts should be inspected carefully before they are work lifting platform, key check whether the screw connection is reliable, hydraulic pipe leaks, loose wires contact with and without, breakage, and so on and so forth. 2, lifting platform lift, put the leg in the four corners, four leg should be firmly supported on solid ground, dispatch work mesa to state level (visual). Turn on the power, the indicator should be on. Then start the motor, pump work, drop one or two in the air, check the parts and then start working again. When the temperature is below 10 ℃, should make the pump running 3-5 minutes, confirmation of oil pump work can be carried out. 3, homework personnel enter the platform after the guardrail doors should be closed, with bolt, tied on safety rope, the center of the load (people stand location) should be in the center position of workbench face.

Send your message to us

*Email

*TEL

*Quantity

*Unit