LED TUBE LIGHT 18W 120CM RA>70 PF 0.6 AC85-265 INPUT VOLTAGE 1800LM GLASS MATERIAL
- Ref Price:
-
$2.90
/ pc
- Loading Port:
- ShangHai
- Payment Terms:
- TT ,LC AT SIGHT
- Min Order Qty:
- 10000 pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
LED Tube Light are receiving global recognition for their energy saving capabilities, long service life ,easy installation and the ability to reduce carbon emissions across a host of different sectors.
Specifications of LED Tube Light..
Voltage:AC85-265V 50/60HZ
Glass
Watt: 20W
PF 0.9
Beam Angle：300 degree
LifeSpan :30,000 Hours
2-3 years warranty
CRI :RA>70,RA>80
CCT；3000-3500K,4000-4500K,6000-6500K
Features of LED Tube Light
The LED Tube Light is widely used and are designed and manufactured to replace the traditional grille fixture ,CFL tubes , the superior SMD LED solution and purity Glass material makes the luminous efficacy high to 100LM/W, it is of excellently heat managed by conjoint structure which maintains the LED working temperature in a comfortable condition.
Excellent Heat Sink
SMD LED solutions
Superior High Quality
Eco-friendly
Energy Saving Perfect Replacement for All Lamp
Blast Free, Starter Free
Applications for LED Tube Light
Replacement CFL for traditional lamp, such as store, supermarket, commerical builing and anywhere
- Q: The LED fluorescent lamp tube breaks the LED light in the inside
- If this is not bad, then look back, there should be a small power supply at the end of the aluminum plate, and the other end of the power supply is 220V. Another possibility is that lower-end LED products will be blocked (non-isolated). Is the aluminum substrate in addition to the SMT chip, also some electronics posted above, if the aluminum board intact, you also to the end, one 220 v mains interface on both ends
- Q: What about the quality gap between leds?
- This one, you may want to consult a professional, I know that so much
- Q: Why is it that when my electric car is charged, the light bulb is burning in the house, and the incandescent lamp is fine, and the other appliances are normal
- It is possible that the high frequency pulse of the charger inside the charger is flowing into the power grid, causing the fluorescent lamp ballast to work and burn down. Electric car charger belongs to the circuit structure of the switching power supply, and the internal vibration circuit is used to produce high frequency signal to drive the transformer. Check to see if the interconnection filter and capacitance component of the inner power source of the charger are damaged. The fluorescent lamp ballast is part of the half-bridge inverter circuit, which is more easily disturbed.
- Q: How does the energy-saving lamp tube set quota
- Energy-saving lamps usually refer to the light source (bulb) as a light source for energy efficiency, as for what quotas to set, and what kind of lamps the source is used for.
- Q: Is a three-male LED fluorescent lamp? How the quality?
- Mitsuo LED bulb, all is by the generation of processing products LED professional production enterprises, from mitsuo buy many, you can increase the cost of quality are ok, but I still suggest you still looking for a professional do the manufacturer of LED lamps and lanterns, will reduce a lot of cost for you!
- Q: What's the difference between an LED fluorescent lamp and an ordinary light tube?
- Leds use low power, long life, low heat and high price.Although it may feel a little bit narrower at 120 degrees, most of the time, it will be enough.
- Q: How do the long daylight bulbs change
- Three kinds: similar to one, but need to take off the lamp foot protection shield first. 4 four kinds: similar to 1 or 2, have lamp tube protection cover, take down protective cover first and same.
- Q: How do LED lamp tube install how connection?
- Leds that do not normally require special orders are mostly built with built-in power, which is directly available. Most can only need to remove the starter on the traditional stent line (is a cylinder bracket highlighted below) mount tubes can be used, if not yet so could you use the stent is a relatively new "electronic" will be a little trouble need you open the stents to get inside the ballast also take off to the inside of the line directly connected to the utility, LED bulb is directly at the mains. Of course, if you understand the circuit and you're not afraid of trouble, it's advisable to remove the "regenerator", because the "ballast" is a power drain.
- Q: What happens to leds if they are not compatible with electronic ballast? What if it's not a bright flash?
- Online are the so-called compatible led ballast, inside it is a constant current for high power led drive power supply, in order to adapt to a variety of different types of leds, it also has different output current varieties, also wants when buying according to the current to select the same current in the led lamp ballast compatible led, it with the ordinary led special-purpose ballast (is actually led a dedicated switch type constant current drive) is the difference on the power (which is the same kind of led do various tubes are common) is large, the range of output current of 300 ma compatible ballast, for example, it can automatically adapt to the current 300 ma from 9 w - any power between 25 w led bulb, but also has the smallest biggest range, the only requirement is that current to be the same.
- Q: 20 square metre room application which led fluorescent lamp tube
- You can choose an 18-watt T8LED fluorescent lamp, or an 18-watt LED light bulb.
Send your message to us
LED TUBE LIGHT 18W 120CM RA>70 PF 0.6 AC85-265 INPUT VOLTAGE 1800LM GLASS MATERIAL
- Ref Price:
-
$2.90
/ pc
- Loading Port:
- ShangHai
- Payment Terms:
- TT ,LC AT SIGHT
- Min Order Qty:
- 10000 pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
