T8 LED Tube SMD Chip High Efficiency 1.2M 20W
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 10 Pcs pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
T8 LED Tube SMD Chip High Efficiency 1.2M 20W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2853 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2853 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li
- Q: In several production workshops of my unit, we will replace a batch of philips T5 fluorescent fluorescent lamps with LED fluorescent lamps. However, it took more than two years to get rid of the old lamp, and it was neither green nor economical, so consult the high man.
- The same way But at the moment there appears to be no systematic recycling system for fluorescent tubes
- Q: The ordinary fluorescent lamp in the home is on the Internet say to remove the hui, the ballast part is short, put on LED lamp tube, can connect to change 3 lamp tube not bright?
- The problem should be: 1, your lamp holder is not in position; 2, the connection of the lamp holder is loose or the wire is broken. No short circuit at both ends of the rectifier. No short circuit in place on both ends of the rectifier, easily between the open flashing voltage is too high, if the LED lamp circuit withstand voltage protection, easy to damage, so suggest tear down ballast, connect the line again.
- Q: The same thing is 5w, is this LED tube power or is this a fluorescent lamp?
- Good, power same power consumption same, this is formed under the same type of floodlight. But the power factor of the LED tube is higher than that of the fluorescent fluorescent bulbs, though not much higher than that.
- Q: Use LED fluorescent lamp tube to replace, the line of original daylight-tube seat should be refitted
- So old ballast, the ballast uninstalled, directly to the card on the two old fluorescent lamp wire short respectively, and then to the outside power, install the LED fluorescent lamp with respect to OK
- Q: How do you measure the flux of the LED fluorescent tube
- No, the illuminometer can only measure illumination. Light flux requires the use of a spectral analyzer plus an integral sphere test. Can go to local lamps and lanterns to inspect department to carry on examination.
- Q: How is the T8LED fluorescent lamp installed?
- Installation is simple, make sure your lamp is single head unipolar or bipolar, single head the two ends of the finished confirm the lamp holder as you the polarity of the two ends of the lamp connected wires, and then directly card directly into the lamp inside
- Q: Does daylight bulbs damage electronic lamp heads?
- Will you get the power wrong? Maybe there's some protection on the lamp that the developer has lost, if you're the new one, you're going to go to the dealership.
- Q: LED T5 T8 and normal fluorescent lamps with no ballast
- A 16W LED fluorescent lamp, equivalent to 40W of ordinary fluorescent lights!
- Q: Does the LED lamp need to be a national compulsory certification
- Do not need, at present domestic do not have mandatory certification, domestic also do not have a unified standard and index! At most, there is the certification of the eu system, ce and rohs. In fact, leds are the most energy-efficient way to make a comparison: We compare 1.2 meter ordinary fluorescent lamp with 1.2 meter LED fluorescent lamp consumption By 20 hours per day: The average fluorescent lamp has a life expectancy of two years, LED fluorescent bulbs have an average life span of six years (the LED fluorescent tube has a lifetime of 4,3800 hours). The 12WLED fluorescent lamp is comparable to a 40W standard fluorescent lamp.
- Q: How do LED lamp tube install how connection?
- If it is a built-in power supply, you need to remove the ballast from the original stents and install them directly.
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.
1. Manufacturer Overview
Location | Shenzhen,China |
Year Established | 2011 |
Annual Output Value | |
Main Markets | Mid East;Western Europe |
Company Certifications |
2. Manufacturer Certificates
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability
a) Trade Capacity | |
Nearest Port | Shenzhen |
Export Percentage | |
No.of Employees in Trade Department | 20 People |
Language Spoken: | Chinese |
b) Factory Information | |
Factory Size: | Above 4,000 square meters |
No. of Production Lines | About 5 |
Contract Manufacturing | OEM Service Offered;Design Service Offered |
Product Price Range | Cheap |
Send your message to us
T8 LED Tube SMD Chip High Efficiency 1.2M 20W
- Loading Port:
- Shenzhen
- Payment Terms:
- TT
- Min Order Qty:
- 10 Pcs pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches