Inground Lighting M-02 Aluminium Body uv resistant exterior paint system

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Body:Die-cast aluminium body,PMMA diffuser.

Finishing:All die-casting components after mechanical and chemical anti-corrosion

treatment, uv resistant exterior paint system.

TECHNICAL CHARACTERISTICS
Type:	Inground lighting
IP Protection degrees:	IP67
IK Protection degrees:	IK10
Light source 1:	4×0.1W 24V AC/DC 28 lm 3000K/6000K lm(N) CRI 75
Total power consumption (W):	0.8
Voltage / Frequency:	100-240V/50-60Hz
Warranty (Years):	3
Units per box:	27
Net Weight (Kg):	0.5
Lm(N): Nominal flow of light in actual working conditions. Its actual flow will depend on the environmental conditions and the efficiency of the optics and/or diffuser.
Kled reserves the right to make the necessary technical changes they deem adequate, in order to improve the features of the
product.
Please consult the sales team to clarify any doubt.

Inground Lighting M-02 Aluminium Body uv resistant exterior paint system

Q: Installation method of buried lamp: Ensure the ground lamp (including underground lamp quality and embedded parts) in underground lamp installation should be mainly about three problems:1, the wiring seal should be done well;Our general wiring buried lights in the special sealing rubber ring and stainless steel fasteners, the wire (in particular, please use the three line wire cable) through the rubber ring, stainless steel wire and then tighten to the firmware can't pull out the sealing rubber ring2, the construction of groundwater should be done to infiltrate, can not let it bubble in the water (because it is not underwater lamp);3, in the buried lamp installed, open the cover, light points for half an hour on the back cover (this step is very important).

Q: Do lawn lamps and buried lights need grounding?: The grounding resistance may not be achieved. However, in our request is not so strict, after all, better than not to do, huh, huh. If you request is too strict, then only when laying the PE power line is additionally provided with a grounding wire, the wire and lead to the power supply connected to the grounding electrode, of course, to measure the grounding resistance.

Q: How to install underground lamp: First of all, in the installation or maintenance of buried lights, should ensure that the power cut off in order to operate. And in the bottom and around the lamp must be laid broken stone and sand, so that it can facilitate drainage and heat dissipation. For its surrounding environment requirements, it is better to non corrosive, flammable and explosive media exist. Note, here to introduce the more important two installation skills: the introduction of line through a coil into the lamp, tighten a coil to prevent rainwater by introducing the line into the lamp body, causing damage to electrical appliances;

Q: What is the opening size of a 250*90 buried lamp?: Correct your point of view, the bridge can not be done in the underground, buried cable through the cable well, through the buried pipe into the distribution room, the bridge with the earth does not matter. You may have just started this scene, you have no count!! Try running more,

Q: The 220V underground lamp into the underground lamp is 12V: Not difficult. As long as the materials are complete and understood, they can be done soon.

Q: Where does the LED underground lamp fit?: Generally, the LED underground lamp is waterproof, so it is used for squares, parks, landscape lighting, lighting fountains, underwater lamps, etc.

Q: Solar LED buried lights, LED solar buried lights, where to sell?: Shenzhen Sheng lighting company's solar LED buried lights, World Expo exhibition hall buried everywhere

Q: Is there any good manufacturer in Ji'nan that uses high-power LED buried lights in the square?: In Ji'nan, a company called Flyover District of Ji'nan City, Huaqing photoelectric lighting factory manufacturers do well I am engaged in quantitative used their lights but LED underwater lights is very bright and well two years warranty I asked Guangdong there are a lot of warranty for one year so I chose this

Q: LED solar lights buried in a big city like high-speed road on the road or pavement, buried in the highway pavement edge is very close to the side, only three of them before and after the flash bulb, have a light bulb, a total of six beads. The Road Pavilion ten meters buried one... Seems to be called spike. Where can I buy or wholesale? (I, Guangxi, Yulin): Recommended: Shandong linuo! Many of our projects here are completed by them, and the quality is very good!!

Q: Installation of LED underground lamp: The lamp body of LED underground lamp is made of high purity aluminum alloy material. The surface is treated by electrostatic spraying, with constant temperature curing and strong adhesion. Generally, it has good waterproof and dustproof property. Before proceeding with the installation work, several aspects should be prepared:1, LED buried lights before installation, must first cut off the power supply. This is the first step in the installation of all electrical equipment, and is the basis for safe operation.2, LED buried lights should be arranged before the installation of lamps and lanterns supporting the various components. Is buried in the underground special landscape LED lamps, once installed less parts, want to re fill the installation is very troublesome. So it should be ready before installation.3, LED buried lights before the installation, should according to the size and shape of embedded parts dug a hole, and then fixed with concrete embedded parts. To isolate the subject and embedded parts of the soil, can guarantee the service life.In addition, before installation, a IP67 or IP68 wiring device shall be provided to connect the external power input to the power cord of the lamp body. Moreover, the LED buried lamp power line requires a waterproof power cord to ensure service life.

Send your message to us

*Email

*TEL

*Quantity

*Unit