Hydraulic Pump AP4VO112TVN(PTO) CNBM CMAX

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1. CE certification
2. ISO9001:2000
3. Brass impeller, carbon steel motor shaft, with thermal protecton inside.

Hydraulic Pump AP4VO112TVN(PTO) CNBM CMAX

Q: Motorcycle not oil, oil pump work well, oil road is not blocked, how to check?: Please ignore the task

Q: Sometimes, cutting machine, bending machine pressure is not enough, I do not know if the hydraulic pump is broken, how should I judge?!: Touch the oil, step inside to see if there is any sense of oil absorption.

Q: Chainsaw engine oil pump is working: The working principle of chainsaw pump: vortex rod drives the turbine to rotate, using the principle of volume ratio, so that the formation of negative pressure inside the tank in the machine, under the effect of atmospheric pressure, the machine oil into oil, transported to the guide plate and the chain. Gasoline engine oil pump assembly is two stroke lubrication system of a large chain saw. It gives the high-speed operation of the chain guide and provide oil to prevent friction when excess heat, causing the chain saw chain guide high temperature and low working efficiency. To complete the task of chainsaw engine lubrication by oil fuel in the two stroke.

Q: 6140 lathe oil pump, no fuel injection, what is the problem?: The fuel pump is clogged,

Q: The working principle of gear type oil pump: What are the working principles and characteristics of gear pumps? The gear pump is a volume type rotary pump, its working principle is: the gear pump has a pair of meshing gears, gear (wheel) fixed on the drive shaft and the shaft end of the gear pump extends out of the casing is driven by a prime mover, a gear pump (driven) installed on the other a shaft gear rotates, the gear pump, the liquid into the suction space along the suction pipe, along the upper and lower shell wall by two gears are respectively extruded into a discharge space (tooth and tooth before confluence), and then enter the pressure discharge tubing. The main features of gear pumps are compact structure, small size, light weight and low cost. Compared with other types of pumps, it has the disadvantages of low efficiency, large vibration, large noise and easy wear

Q: My car is old Mondeo 6 cylinder, is about 04 years, did not open at home for more than a month, another time machine pump indicator lights, is not always bright, is running 10 meters light, then I re open flameout is good, but there are more than ten meters and bright, so repeated always dare not open far. What's the matter? The oil is absolutely lacking. Please give me some answers, my friends. Thank you.: Low oil pressure time lamp is bright, the cause of the low pressure oil pump is a bad may have no pressure, pressure sensor two is broken there is no pressure signal, then the oil filter is blocked and no pressure, although the oil chamber has no pressure oil but also can burn out bush. In short, there must be a fault, but have to go to the factory as soon as possible to check it.

Q: What are the markings on the fuel pump and the oil pump? They can be recognized at once: This question is a bit wonderful to say, petrol pump is generally the only plastic pump heart is generally car iron sight to see and open the oil pump in the engine oil pan on the oil pan general can see are generally open Aluminum Alloy.

Q: JMC 462Q engine does not go to the cylinder head, where is the oil pump located?: You can't fix it by yourself.1, remove the valve compartment cover, you can see the rocker shaft, loosen the top of the middle fixed screws.2 you can blow it up in a high pressure air pump, clear it up, start the engine, and spray the oil outward.3, also can use steel wire (about 50cm long, rough 1mm or so, can reach that hole), to dredge, must exceed 25mm (cylinder head height) just go.4 or more can not work, and finally only remove the cylinder head.The 5 reason is that the cylinder pad (oil hole) is blocked by carbon deposits, and the engine oil can not reach the rocker arm.

Q: How to solve the blockage of the automobile oil pump?: Gasoline pump, pump can not afford oil, may have the following aspects.1, the circuit is not smooth, this is very good inspection, with Multimeter or test light on the plug, play the motor light, indicating that there is electricity, no lights, indicating circuit failure.2, circuit fault, first check the oil pump, relay and oil pump fuse, when motor, oil pump relay should be pulled in, there is voltage output. If there is no voltage output, consider the oil pump, relay, or computer circuit to the oil pump, or even a drive computer.3, if there is electricity, it is much simpler, pull out the oil pump, the oil pipe, motor. When oil is out, check that the pipe is blocked and the gasoline pump is removed without oil.4, the gasoline pump if there is no foreign body plug, then you can change it directly!

Q: GY6 engine oil pump installation direction, there is an arrow pointing to the other side of the ah: The arrow points to the direction of the oil outlet, with the arrows connected to the engine oil inlet

Send your message to us

*Email

*TEL

*Quantity

*Unit