Hand Stacker--EFS1016(G)/1030(B)

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

PRODUCT NAME:Hand Stacker--EFS1016(G)/1030(B)PRODUCT INTRO

The hydraulic pump uses the newest technology

Special C-shaped steel helps provide strength and rigidity

Adjustable forks for various needs

Save time and manpower

Conforms to CE safety standard

Conforms to EN1757-1

Related Products

Q: How much is the 8 square meter tatami mat: Also, it is just 2 meters * 4 meters = 8 square meters, materials cost more than 1000 yuan, the thin woodworking board of the use of the frame, the Chinese fir wood gusset plate, the worker wages 200 days

Q: What about the heat treatment of the lifting platform?: Ball screw work is often subjected to bending, torsion, fatigue and shock, while also bearing friction on sliding and rotating parts. The damage form of ball screw is mainly worn and tired. Therefore, its performance requirements as a whole must have good comprehensive mechanical properties (that is, a certain amount of strength and toughness) and high dimensional stability, working parts (raceway, diameter of axle) requires a high hardness, high strength and wear resistance. You are recommended to go to hymanu

Q: How does hydraulic platform change sealing ring, how to operate: Dismantled after checking in parts, parts should be stored in a clean environment, and add to prevent knock against the isolation device, with professional pliers to take out the seal, after installing the new seal, again before assembly, parts should be cleaned.

Q: What is the reason for the automatic lowering of the hydraulic platform: The hydraulic lift can rise steadily or maintain position because of the pressure oil in the cavity.

Q: The ball of the universal milling and lifting platform rolls off, how to install,: Screw pair after repair good, reinstall the screw pair, need to find a good accuracy of each connecting parts, including position accuracy, positioning accuracy, etc., such as straightness, coaxial degree, parallel degree, diameter jumped, end or something. This is easy to say, but it takes care and patience to do it, and it is usually done by experienced machinery-fitter or fitter. If you can't do it, call the line cutting manufacturer and ask them to repair it.

Q: Where do the elevator motors go?: The earliest elevating equipment appeared in ancient China and Europe, a kind of "windlass" that was used to transport people and goods vertically. In modern times, we use a wooden ladder for lifting goods, which is inconvenient and dangerous to climb. On March 23, 1857, a fifth floor store in New York City installed the first passenger lift with the Otis safety device. The first lift was powered by a steam engine, so the building must have a boiler room. In 1880, the German company Siemens invented the electric lift, and since then, the use of elevators has been widely accepted and developed rapidly. Domestic production The electric lift machine, the product model is different, the upgrade height is 4 meters, 6 meters, 18 meters. Adopt foreign hydraulic, pump station system, hydraulic system explosion-proof device and hydraulic self-locking device. It has the advantages of novel design, reasonable structure, lifting and balance, simple operation, convenient maintenance and other products. Widely used in plant maintenance, industrial installation, equipment maintenance management, warehouse, aviation, airports, ports, railway stations, mechanical, chemical, pharmaceutical, electronics, electric power and other high-altitude equipment installation and maintenance.

Q: To make a four trapezoid screw lifting up seven tons of lifting platform should be matched with the straight screw and motor: Force teck can offer the synchrolifting lifting system design, a full set of accessories combination: spiral elevator, commutator, drive shaft, shaft coupling, gear motor, as well as the system, a full set of CAD drawings, and the scene debugging

Q: What is the size of the hydraulic elevator platform for 2T: Stationary hydraulic lifting platform is to provide parameters to custom-made according to customer, not the size of the regulations, the mesa size parameters have the requirement of the clients, commonly movements itinerary, load, lift platform height, is there any need to ask me,

Q: The structure of the universal elevator milling machine: The main shaft, the bed, the platform, the platform, the rotary table, the base, the suspension girder, the pole bracket, the work of this mill is more detailed

Q: There are different kinds of milling machine and vertical lifting machine milling machine: Start by figuring out the difference between vertical and horizontal The main shaft of vertical milling machine is perpendicular to the workbench, and the spindle of horizontal milling machine is parallel to the workbench. The knife of vertical milling machine is relatively flexible, the scope is wider. Can use vertical milling cutter, machine clip, bit etc. Milling keyway, milling plane, boring hole, etc.

Send your message to us

*Email

*TEL

*Quantity

*Unit