Ductile Iron Valves DN100
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 PCS
- Supply Capability:
- 1000 PCS/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Structure of Gate Valve Description:
A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed.When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.
2. Main Features of the Gate Valve:
• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber
• Free of water pollution
• High manufacturing accuracy
• High strength
• Environmental protection and energy saving
• Good visual effect
3. Images
4. Gate valve Specification
5.FAQ
1. What's are the characteristics of gate valve?
The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel.
2. What is the work principle of gate valve ?
The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry.
3. What is the structure?
Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.
- Q:What is gate valve (with force transfer joint)?
- The force transfer joint is mainly used for the loose connection of pumps, valves and other accessories.
- Q:What is the difference between the cut-off valve and the gate valve?
- What is the difference between gate valve and stop valve?:Gate valve and globe valve structure is different, the valve structure for hand wheel, with the stem rotating together to do the opening and closing movement. Valve structure is rotating handwheel, stem do lifting movement. The flow is different, the gate valve requires full open or full closed state, the cut-off valve does not need. The valve has the flow direction requirements, and the gate valve has no inlet and outlet requirements!Sealing performance comparison:Valve length is shorter than the cut-off valve, higher than the cut-off valve, the valve should pay attention to the installation of high elevation. The gate valve can be tightly closed with the sealing surface by the pressure of the medium so as to achieve the effect of not leaking.
- Q:What's the difference between a soft seal gate valve and a hard sealed gate valve?
- It uses the elastic material of the gate, and uses the elastic material to produce the micro deformation compensation effect. It can achieve good sealing effect. Soft sealing gate valve has the advantages of light switch, reliable sealing, good elasticity memory and long service life.Hard sealing surface of the gate valve for cast iron or stainless steel, open and close resistance is small, no flow, but poor sealing performance.
- Q:Installation and operation instructions of knife gate valve
- 5., when installing the valve, users must reserve the necessary space for valve actuation;The wiring of the 6. driving device shall be carried out according to the wiring diagram;7. knife gate valve must be regularly maintained, shall not be arbitrarily collision and extrusion, so as not to affect the seal.
- Q:Does the tap belong to a stop valve or a gate valve?
- Most taps are stop valves:1, gate valve (gate valve) is a headstock ram, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed doors, discomfort pumpsparameters vary, usually 5 degrees is not high, medium temperature is 2 degrees 52'. To improve its manufacturability, make up for the deviation of the angle of the sealing surface during processing. This gate is called an elastic ram.2, valve (stop, Globe, Valve) of the opening and closing parts are plug shaped valve, sealing surface is flat or sea cone, the valve along the center line of the valve seat in a straight line movement. Stem form of exercise (generic name: dark bar), but also lift rotating rod can be used to control air, water, steam, all kinds of corrosive media, mud, oil, metals and radioactive liquid media and other types of fluid flow. Therefore, this type of shut-off valve is very suitable for cutting or regulating and throttling. Because of the valve stem to open or close the trip is relatively short, but very reliable cut off function, and because changes in the valve seat and the valve stroke is proportional, is very suitable for flow regulation.The stop valve is an ascending stem type, and the handwheel rotates and rises along with the stem. Valve is hand wheel rotation, stem upward movement. Flow is not the same, the gate valve requires full open, the cut-off valve is not the same. The gate valve has no inlet and outlet direction requirements, and the cut-off valve has the required inlet and outlet!
- Q:Yes, soft sealing gate valve can reach 25 kilograms, Fujian light valve company has this type of soft sealing gate valveAnonymous browsing | 28 times
- Soft seal butterfly valve seal is good, but can only withstand up to 16 pressure, or the plastic can not stand. A short period of time is OK, and it's also related to the workmanship and quality of the factory. The quality is poor.
- Q:What are the advantages and disadvantages of flat gate valves?
- The advantage of flat gate valve is that the flow resistance is small, and the flow resistance is similar to the flow resistance of short valve. The flat gate valve with guide hole is installed on the pipeline and can be directly cleaned with the cleaner. As the gate is sliding on the two seat surface, the flat gate valve can be applied to the medium with suspended particles, and the sealing surface of the flat gate valve is actually positioned automatically. The seat seal surface is not subject to thermal deformation of the valve body. Moreover, even if the valve is closed in cold condition, the thermal elongation of the stem will not cause the seal to be subjected to overload. The length of the structure is much shorter than that of the ball valve, and it is easier to start. Light plate gate valve is more refined, but the effect is exactly the same.
- Q:What is the soft seal gate valve?
- Commonly used soft sealing gate valve model is divided into: Z45X and Z41X, the difference is that the Z41X is the Ming bar, and Z45X is dark rod.Matters needing attention in packing and transportation of soft sealing gate valve:Soft sealing gate valve before transport, should use the rope to tie up the small caliber.Before transportation, the lighter sides of the valve should be sealed.For larger caliber soft sealing gate valve, it should be used to carry out simple packing, it can better prevent the valve in the process of transportation damage.
- Q:Gate valve type Z40Y, Z40H letters - what does that mean?
- According to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== connection: flange0== structure: wedge type elastic RAMY== sealing surface material: hard alloyH== sealing surface material: Cr13 stainless steel
- Q:What is plug welding gate valve?
- Plug connection pipeline welding mode safety gate valve
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Ductile Iron Valves DN100
- Loading Port:
- China main port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 PCS
- Supply Capability:
- 1000 PCS/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords