Gate Valve Non-rising Stem with Price and High Quality
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.Structure of Gate Valve Description:
A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed.When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.
2. Main Features of the Gate Valve:
• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber
• Free of water pollution
• High manufacturing accuracy
• High strength
• Environmental protection and energy saving
• Good visual effect
3. Images
4. Gate valve Specification
5.FAQ
1. What's are the characteristics of gate valve?
The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel.
2. What is the work principle of gate valve ?
The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry.
3. What is the structure?
Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.
- Q:Fire protection gate valve from the wall how many distance there is no regulation?
- 1 meters away from the wall, leaving the maintenance and replacement distance
- Q:Stainless steel gate valve DN150 200300 weight, who knows?
- Valve selection of different driving methods, connection forms, structural forms, nominal pressure, sealing surface materials, lining materials, valve body material will affect the weight of the gate valve more or less, it can not be generalized.Take my commonly used Z41H-16P (i.e. PN1.6MPa) series stainless steel gate valve as an example, and the weight of DN150/200/300 is 134/192/379kg. Of course, different manufacturers may vary in weight, but not much.I hope I can help you.
- Q:What is the difference between the cut-off valve and the gate valve?
- What is the difference between gate valve and stop valve?:Gate valve and globe valve structure is different, the valve structure for hand wheel, with the stem rotating together to do the opening and closing movement. Valve structure is rotating handwheel, stem do lifting movement. The flow is different, the gate valve requires full open or full closed state, the cut-off valve does not need. The valve has the flow direction requirements, and the gate valve has no inlet and outlet requirements!Sealing performance comparison:Valve length is shorter than the cut-off valve, higher than the cut-off valve, the valve should pay attention to the installation of high elevation. The gate valve can be tightly closed with the sealing surface by the pressure of the medium so as to achieve the effect of not leaking.
- Q:What are the standards for the execution of cast iron dark pole gate valves?
- Standard Specification for cast iron blind rod gate valves:1, design and manufacture: according to the provisions of GB/T12234-892, structural length: according to the provisions of GB/T12221-893, flange size: according to the provisions of JB79 GB/T9112-91314, inspection and test: according to the provisions of JB/T9092-99 GB/T13927-92Drive mode: manual, electric, gear drive;
- Q:What gate valve is the J41H-150LBDN100 gate valve?
- Its closing principle is to rely on the valve bar pressure, so that the valve sealing surface and seat sealing surface close together, to prevent the circulation of media. The cut-off valve is divided into three kinds: straight through type, right angle type and direct current type oblique stop valve.
- Q:Is the gate valve flanged?
- The most commonly used gate valves are threaded connections, flanged connections, and welded connections.Like the outer thread connection, the clamp connection, the card sleeve is seldom used.
- Q:Gate valve z45h-10dn250 length of the body?
- Z45h-10dn250 body length L=330mm, this valve is hidden bar, elastic seat, sealing gate valve, gate lining, lining fluorine, belong to soft seal
- Q:What are the meaning of the cast rigid gate valves z41h-16c?
- According to the provisions of the JB/T 308-2004 valve type programming method:Z== gate valve4== flange connection1== rigid single gateH== sealing surface material: Cr13 stainless steel16== pressure rating: 1.6MPaC== body material: carbon steel
- Q:Why? God, can you explain to me in detail why?
- Check valve in the valve in front. To prevent water from flowing back.
- Q:What's the difference between open rod gate and dark rod gate valve?
- 4, the dark pole gate valve height smaller size; Ming rod gate valve requires a larger installation space;5, the structure of the rod gate valve is beneficial to the lubrication of the valve stem, and the degree of opening and closing is obvious. The stem thread of the dark rod gate valve is not only unable to lubricate, but also directly accepts the medium erosion and is easy to damage. Therefore, the open bar gate valve is used more widely
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Gate Valve Non-rising Stem with Price and High Quality
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords