Ductile Iron Butterfly Valve Of Top Quality
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 1000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description:
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images:
4.Manual Wafer Butterfly Valve Specification:
Size: DN40-DN1200
Nominal Pressure: PN10/PN16
Operation Temperature: ≤200°C
Suitable Medium: Water,Steam.
5.FAQ
1) What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2) How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3) What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q:Where is it installed, what is the role, what is the material, and are there other alternatives instead of this effect?
- Mainly from the role of sealing, to prevent leakage of the valve conveying medium, stuffing commonly used PTFE, graphite, asbestos packing three.
- Q:Representation of several types of valves
- Valve type:Z gate valveJ stop valveL throttling valveQ ball valveD butterfly valveH check valve and bottom valveG diaphragm valveA safety valveT regulating valveX plug valveY pressure reducing valveS trapDZ solenoid valveO electromagnetic motionDrive mode:1. electromagnetic and hydraulic action2., electricity, a liquid3. worm gear4. the spur gear rotates5. bevel gear rotation6. pneumatic7. fluid movement8. air and one liquid movement9. electricOther hand wheel, handle, board hand, no performanceSide mode;1. internal thread2. external thread3. flanges (for double spring relief valves)4. flanges5. flanges (for lever type, safety door, single spring safety door)6. welding7. pairs of clips8. clamps9. card sleeveIllustrated cover or lining:T copper alloyH alloy steelB tin based shaft (bearing alloy)Y cemented carbideX rubberJ hard rubberSA PTFESB poly three fluoro ethyleneSC polyvinyl fluorideSD phenolic plasticsSN nylon
- Q:Measure the temperature with a thermocouple, and then how to make the valve open when the temperature reaches a certain value. When the temperature is lowered, will the valve be closed?Or tell my brother what is the knowledge, I can see it myself. Good. How much extra?!
- Switching type (one on and off)Block digital display with the upper and lower limit control valve opening and closing is goodProbably more than 100Regulating type (to keep temperature at a constant value)With PID valve position regulator can be very good controlAbout 300 more
- Q:What does the valve "4" mean?
- Refers to the size of the wire tooth, usually refers to the internal and external teeth 4 points, also known as DN15, the outer diameter is 20mm
- Q:The general signal valve installation, or other valve installation is not installed with the groove flange clamp hoop Yucca or direct way? What's the convenient way to install the following diagram? I don't understand. Neither groove, flange nor hoop. Thank you, sir!
- The installation of the signal valve is in accordance with GB50261-2005The 5.4.6 signal valve shall be installed on the pipe in front of the flow indicator, and shall not be less than 300mm from the flow indicator.The other valve control valve installation, specification, type and location of installation shall comply with the design requirements, the installation direction should be correct, control valve should be clean, no blockage, no leakage; the main control valve should be added headstock logo, the control valve cover shall be provided to indicate position of the mark in the position.1. The installation of the exhaust valve shall be carried out after the pressure test and the flushing of the system pipe. The exhaust valve shall be installed at the top of the water distribution dry pipe and the end of the distribution pipe, and no leakage shall be ensured.2, the valve flow direction should be consistent with the direction of flow in the water supply pipe, water inlet side of the filter is installed, and should be installed in the control valve; the adjustable valve should be installed horizontally, the valve cover should be upward; the proportional valve should be installed vertically: when the level of installation, the valve orifice hole single breath we should double down, breathing valve whose orifice should be in a horizontal position.3 other control valve should be installed to keep a certain distance, to facilitate maintenance and management, installation of multifunctional pump control valve itself with pressure gauge, pressure gauge should be installed in the adjacent parts; import should be prevented in the back before the installation or use of the filter with filter backflow preventer, backflow preventer at both ends the valve should be installed separately, and at least one end of the flexible joint should be installed;
- Q:How big valves are used in the DN90 pipeline?
- If you use a 97 tube, the inner diameter of 89- phi 90., nominal pressure is low, then try to use DN80, DN80 valve diameter of 80, you can try butt welding
- Q:the rest are hot, the living room outside all the heating pipe valve closed, the living room heating is still not hot, after the water for a while hot, and cold
- There is gas, causing water not to cycle, give up on the cure! Are you single family control?Single family control, the general bedroom and living room is not all the way, the living room, this way, the vent valve in the toilet, I was on the road in the balcony! The bleeder valve, is made of copper tube in the device above two, as long as can step in his place, the bleeder valve with a small angle, feet above a needle, with a needle to drill a well, there is a long time not float, a gas exhaust out that leads to water circulation,Why do you put a little while, the water is hot, a little cooler, the water does not cycle, is dead water, can not cool it?I am building plumbing, believe me, yes, these are some common problems, especially on the top floor!
- Q:What does LBC mean in a valve?
- LB and 800 are together. 800LB means 800 pounds of stress, and P should be PRESSURE.
- Q:The low pressure in our factory is below 1.6Mpa, medium pressure is 2.5-6.4MPa, high pressure is 10-80MPa.Where's qusetion:1.6-2.5Mpa??? Which section does it belong to?. I think many of them are defined on the Internet But I didn't say, where's 6.4-10Mpa?
- In fact, this is only the valve industry sector argument, not necessarily to distinguish between very clear.As long as the customer pressure requirements, we give him the drawings on it.Valve flange thickness and valve thickness are not standardized, according to pressure requirements.The flange thickness of 6.4Mpa and 10Mpa is completely different from that of valve body.For example: general gate valve, the most basic pressure 1.6MPa, according to GB/T139272008 and JB/T90921999 standard castingGenerally selected 1.6MPa, when the highest pressure pressure is 1.6X1.5=2.4MPa, if you exceed this pipeline pressure is not, there are now many manufacturers in order to save costs, the valve wall is thin, a conventional valve pressure 1.6MPa is a bit difficult.My own boundaryVacuum negative pressure 0.05Mpa-0.5Mpa0.6Mpa-1.6Mpa belongs to normal pressure (low pressure)2.5Mpa-4.0Mpa belongs to medium pressure6.4Mpa-10Mpa-16Mpa-25Mpa-32Mpa-42Mpa belongs to high pressure50Mpa-80Mpa belongs to supercritical high pressure valve
- Q:Tell me the exact address, or the phone number in the market. Where is the industrial zone (the valve) in Hefei? Please help, thank you
- On the valve network to find the best, you can find the valve business in Anhui
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Ductile Iron Butterfly Valve Of Top Quality
- Loading Port:
- Tianjin
- Payment Terms:
- TT or LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 1000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords