aluminium roofing sheet making machines
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 30 sets set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
aluminium roofing sheet making machine
1.. Processing technique and deployment
Flow chart : Decoiler-- Roll Forming--PLC System—Hydraulic System –Pressing --Cutting —Output Table
No. | Name | Unit | Qty |
1 | Decoiler | set | 1 |
2 | Main Machine for roll forming | set | 1 |
3 | Control System(PLC) | set | 1 |
4 | Pressing System | set | 1 |
5 | Cutting System | set | 1 |
6 | Output Table | set | 1 |
material:
Processing material | colored steel plate, galvanized plate, or aluminum plate |
Material thickness | 0.3---0.8mm |
Material hardness | 195 mpa---350 mpa |
Forming speed | 8-12m/min |
Working speed | 5-8m/min |
Uncoiler
Usage | It is used to support the steel coil and uncoil it in a turnable way. Passive uncoil pulled by roll forming system
|
Loading capacity | 5T |
Uncoiling width | 1250 |
Inner diameter | 450-550mm |
Entry Beach
Usage:Put the raw material(steel plate) through the beach to manufacture and process,
it can guarantee that the products are neat, parallel and everything is uniformity.
Please refer to the equipment regulation to know the function of locate angle iron.
Main parameters of aluminium roofing sheet making machine | ||
1 | Length of the main part | about 10500*1650*1500mm |
2 | Weight of main part | 7.5T |
3 | Voltage | 380V/50HZ 3Phase |
4 | Roller fixer | middle plate |
5 | Frame | 350H steel |
6 | Drive mode | chain |
7 | Material of rollers | 45#steel, surface hard chromium plating |
8 | Material of shafts | 45#steel |
9 | Diameter of shafts | φ 80mm |
10 | Number of rollers | 18 rollers |
11 | Main power | 5.5kw |
12 | Material of mould | Cr12 quenched |
13 | Power supply | hydraulic power |
cutting device
The cutting blade controled by the hydraulic system
It adopts the hydraulic drive and automatic location to decide the dimension and cut the target products.
Material of blades | Cr12 quenched |
Power supply | hydraulic power |
Components | It contains one set of blade, one hydraulic tank and one cutter machine. |
Power | 5.5KW |
the machine naked in the container or packing as your required.
Payment: 30% T/T in advance and balance 70% after inspection confirmation before shipment.
Delivery: within 45 working days after receipt of deposit
Guarantee: One year, and we will provide the technical support for the whole life.
- Q: What steps are required during the installation of the cement tile machine?
- Board installation and commissioning: the board and the plate machine board axis, along the axis direction adjustment board machine so that the board machine in the hanging board down when the tray does not collide with the board, adjust the board lift Induction switch position to determine the number of yards of brick, up to no more than 3 board.
- Q: Analysis on the Problems of Cement Shade Machine
- Pan alkali base water, alkali or salt content is too high, the water vapor will bring out the salt and the bottom of the film or surface precipitation; tile body alkaline, in the water after the alkali will be discharged through the pores, the formation of small bubbles. Remove all the affected and the loss of adhesion of the film, to be fully dry tile body, treated with oxalic acid and washed with water, dry and then brushing; follow the construction specifications, do grass-roots waterproof, to ensure that the substrate conditions meet the construction requirements. Gloss uneven uneven base layer is not uniform, the adsorption of the film is not high; film thickness is not uniform; the same side using different construction tools; the same side using different batches of products.
- Q: The processing method of the tile machine
- The billet is soft. Filter cloth part of the paste was dead, the next model of the local filter hole blocked, clean up. System without pressure, pump reversal: wiring error, adjust the steering. Insufficient power: motor failure or low voltage, power supply or repair motor. Oil pump temperature is too high: oil viscosity is too low, the pump is damaged, the cooling is insufficient or interrupted.
- Q: What are the advantages of cement tile machine?
- A machine multi-purpose, tile mode switch fast, fool-type operation, low power, CNC molding. Unique design, multi-functional hydraulic molding, user-friendly interface operation, advanced and reasonable layout, to fill the gaps in the domestic.
Send your message to us
aluminium roofing sheet making machines
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 30 sets set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
