Transparent Color PE Protective Film W120-50T
- Loading Port:
- China Main Port
- Payment Terms:
- TT Or LC
- Min Order Qty:
- 10000 Square Meter m²
- Supply Capability:
- 100000 Square Meter Per Month m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Application: PE protective film can protect glass from dirt and scratch during transporation and installation. It can save your time doing the cleaning.
2. Transparent color, transparent blue color, black & white color, white color, red color and so on available as per customers' requirements.
3. The choice of surface protective film depends on the surface: material and roughness. Tell us what surface you want to protect and we will recommend proper film to you.
Technical Data of Transparent Color PE Protective Film W120-50T
Item Number: W120-50T
Carrier: PE (polyethylene) film
Thickness: 50micron (0.05mm)
Peel Adhesion: 120g/25mm
Adhesive: water acrylic
Color: transparent
Temperature Resistance: 60C 48hours no residue
Elongation: ≥250%
Inner Diameter: 3" (76mm)
Length: within 3000meter
Widh: within 1.5meter
Recommended jumbo roll size: 1.0m x 1000m
Packing of Transparent Color PE Protective Film W120-50T
Wrapped with kraft paper or carton.
Remarks of Transparent Color PE Protective Film W120-50T
A. The data above are typical results and subject to change without notice.
B. Tolerance: 5%
C. The products should be stored at room temperature and be kept away wet and/or heat source.
D. It is essential, the surface of film must be clean, dry, and free of grease and oil.
E. The users should take test and do trial-application on the above product before coming into application so as to witness and ensure suitability for their special purpose and technique
- Q:When you remove the protective film from your cell phone, how can you remove the glue?
- The organic matter and the inorganic substance in the reaction can be dissolved, the contact area is increased, and the reaction rate is increased. For example, in the saponification reaction of oils and fats, the addition of ethanol can dissolve NaOH and dissolve oil, so that they can contact fully in the homogeneous phase (the solution of the same solvent) and accelerate the reaction rate.
- Q:What are the requirements for PE protective films?
- The requirements for the use of PE protective films are as follows:Suitable viscosity: easy to paste and tear easily;The peeling force is stable: the change of the time is small, that is to say, the smaller the lifting force is, the better the better;
- Q:How to get rid of the aging protective film on stainless steel?
- Apply some rosin water at first. And then wipe it off with toilet paper or dry cloth.
- Q:How many kinds of materials can be used to produce the protective film for flooring finish?
- Commonly, the materials used in the protective film for flooring finish can be classified into: PE (polyethylene), PET (polyester), CPP (polypropylene), PVC (polyvinyl chloride), OPP, etc. 1.PE films have many colors. The most common colors are transparent, blue, black and white, as well as milky. Apart from these, there are black, grey, green, yellow, orange, gold, red and so on. PET films are usually transparent, grey and golden. 2. Usually, CCP film is matte. It's a kind of film with foggy effect. 3. PVC film is often transparent. Apart from that, there's a kind of blue static film. 4. OPP film is generally transparent and adhesive. Among all, the types of PE film are the most including PE adhesive film, PE static film, PE textured film, PE stretch film and PE packaging film. The adhesion of such film can be classified into degrees from 5g to 270g; and the thickness, from 1.5C to 15C. The adhesion of the most widely used film is 5C. PET films can be divided into PET film with silica gel, matte PET film, three-layered PET film, Single-layered PET film, two-layered PET film and PET release film. PET protective films are usually used on the protection of a variety of screens. PET release films are often used in the punching of PET protective films in die cutting factories. The adhesion of most commonly used punching is 5C or 7.5C. And the adhesion of the most commonly used release film is 2.5C, 3.8C, 5C or 7.5C. PET color is generally transparent, gray, gold.
- Q:How can the protective film on the burglarproof door be removed after sun exposure?
- Or dry powder, with a sticky cloth to rub flour, and a little bit of attention, do not scratch the door on the line
- Q:What's the difference between the film with by Cheyishang company and the ad film on buses, the protective film coated on new cars as well as other kinds of film?
- There are great differences. The ad film used on buses would curl after using for a long time. The adhesion strength of its backing gum is not good enough. And the protective film coated on the paint of new cars is usually transparent or white. It's too thin that the protective effect is not good. Glue and its residue may remain when tearing it off after a long time. And it has poor ductility.
- Q:Why should tear off the protective film on kitchen ventilator?
- It's up to you. If you like it clean, then keep it coated. If you want to see the protective film without anything covering it, you can just tear off the film.
- Q:How many kinds of material are there in the decoration ground protection film?
- Best answerDecoration ground protective film in accordance with the material commonly used:PE (polyethylene), PET (polyester film), CPP (polypropylene), PVC (PVC), OPP, etc.
- Q:The protective screen of the screen is dirty. How do you clean it?
- One, soft cloth + water, at this time, LCD is often only a little dust, so clean up to be simple and easy. You just need to use a piece of wet soft cloth to gently wipe off the dust on the LCD surface. Notice that this cloth is not too coarse, otherwise it will make the screen scarred. In addition, soft cloth must be wrung, because water is the natural enemy of LCD. After cleaning, dry the wet traces.
- Q:How to remove the shadow of the keyboard protection screen in the notebook screen?. With the lid on, after a night, there was a watermark, which was of poor quality
- Not bad quality, when you are playing, the computer will heat up, and your keyboard covered with protective film, the heat under the keyboard, and then shut the lid immediately after the shutdown,
1. Manufacturer Overview |
|
---|---|
Location | Dongguan, China |
Year Established | 2004 |
Annual Output Value | US$ 10 Million |
Main Markets | 20.00% North America 20.00% South America 10.00% Eastern Europe 10.00% Southeast Asia 10.00% Northern Europe 10.00% South Asia 10.00% Western Europe 5.00% Africa 5.00% Mid East |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Shenzhen Port |
Export Percentage | 10% |
No.of Employees in Trade Department | 50-100 People |
Language Spoken: | English; Chinese; |
b)Factory Information | |
Factory Size: | Above 30,000 square meters |
No. of Production Lines | Above 3 |
Contract Manufacturing | protective film |
Product Price Range | High; Average |
Send your message to us
Transparent Color PE Protective Film W120-50T
- Loading Port:
- China Main Port
- Payment Terms:
- TT Or LC
- Min Order Qty:
- 10000 Square Meter m²
- Supply Capability:
- 100000 Square Meter Per Month m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords