Switch Power Supply 12V 15 Watt for LEDs
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 10 Pieces pc
- Supply Capability:
- 10,000 Pieces per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification:
| Model | ||
HS-15-5 | HS-15-12 | HS-15-24 | |
DC output voltage | 5V | 12V | 24V |
Output voltage tolerance(Note:2) | ±2% | ±1% | ±1% |
Rated output current | 3A | 1.3A | 0.7A |
Output current rage | 0-3A | 0-1.3A | 0-0.7A |
Wave and noise(Note :3) | 50mVp-p | 50mVp-p | 100mVp-p |
Inlet stability(Note :4) | ±0.5% | ±0.5% | ±0.5% |
Load stablity (Note :5) | ±1% | ±0.5% | ±0.5% |
Efficiency | 76% | 78% | 80% |
Adjustable range for DC voltage | +10,5% | +10% | +10% |
AC input voltage range | 170-264VAC 47-63Hz;240-370VDC | ||
0.25A/230A | |||
Cold-start current 30A/230V | |||
<0.5mA/240VAC | |||
105%-135% hiccup mode,auto recovery | |||
±0.02%/°C(0-50°C) | |||
200ms,100ms,30ms | |||
10-500HZ,2G 10min,/1cycle,Period for60min,Each axes | |||
Input and output internal:1.5KVAC,Input and enclosure:1.5KVAC,Output and enclosure:0.5KVAC | |||
Input and output internal:Input and enclosure,Output and enclosure:500VDC/100MΩ | |||
-10°c~+60°c(Refer to output derating curve),20%~90%RH | |||
-20°c~+85°c 10%~95%RH | |||
84×58×38mm | |||
0.15Kg, 80pc/CTN | |||
- Q: 1000 square meters low voltage.36 volts lighting power supply with multiple transformers and wires
- You must know the quantity and power of the lamp to determine the transformer
- Q: How to use digital multimeter to detect the quality of 36 volt low voltage lighting transformer?
- General digital multimeter has a capacitor (some of the files with a million capacitance test table of Jack, some use pen)
- Q: Why is elevator lighting transformer installed?
- 9.4.5 well distribution shall comply with the following requirements:1 the elevator hoistway shall be dedicated to the elevator, and no equipment, cables and other devices related to the lift shall be installed in the hoistway.2 the well shall be provided with illumination, and the illumination shall not be less than 501x, and shall comply with the following requirements:
- Q: Is the substation separate from the power and illumination transformer?
- The power and lighting power supply in the substation need not be separated. In a large capacity power plant, the lighting can be electrically powered to ensure that the generator is stopped. The lighting source is often separated from the lighting transformer and powered by other power supplies.
- Q: The transformer zero line has broken, has the result to the household illumination circuit?
- The power supply system in three-phase four line zero line is broken, the breakpoint of the single-phase circuit (220V) electrical burn by voltage to 380V. I met, the incandescent lamp suddenly particularly bright then the blow up of internal fuse TV has burned out. So in the three-phase four wire power supply system zero line asked to do repeat grounding in households is the reason.
- Q: Does the lighting work properly? Doesn't that power equipment start voltage unstable?
- As long as the capacity of the transformer is enough, the voltage fluctuation of the line will be sure to occur when the high power equipment is started. Such fluctuations do not have much impact on the lighting.
- Q: Why the 21 lighting transformer must double winding type safety isolating transformers, prohibited the use of autotransformer.
- Double winding type safety isolating transformer is provided with two windings respectively as input and output (primary) winding (secondary) winding, and between the two windings are insulated from each other, only through the magnetic connection to the power supply, which is the secondary winding and the earth does not constitute a loop, if the use of additional electrical insulation, it should be safety isolating transformer.
- Q: Can the 500 volt lighting transformer be changed into an electric welder?
- The no-load voltage is higher (about 70~90 V), the arc can be smoothly started, and the voltage will be reduced to about 30 V when welding.
- Q: Please tell me how to calculate the transformer in the lighting circuit of elevator shaft in building electrical design
- Pe=19.5KW, installed capacityKx=1 coefficient of demandPjs=KxPe=19.5KW, calculated loadCOS, phi, =0.85, power factorIjs=KxPe/3/220/cos phi (Ijs calculates current, voltage, 380V/220V, three-phase)=1*19.5*1000/3/220/0.85=34.76A
- Q: Lighting, lights, transformers, bulb brightness is too low, what's the matter?
- Generally, the power of the transformer is the apparent power, and the light bulb is the active power, and the power matching is taken into account.
1. Manufacturer Overview
Location | Shenzhen, Guangdong, China (Mainland) |
Year Established | 2011 |
Annual Output Value | US$5 Million - US$10 Million |
Main Markets | North America; South America; Eastern Europe; Southeast Asia; Mid East; Western Europe; Central America; Northern Europe; South Asia |
Company Certifications | ROHS Test Report; Waterproof Power Supply CE-LVD; Waterproof Power Supply CE-EMC; CE-LVD |
2. Manufacturer Certificates
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability
a) Trade Capacity | |
Nearest Port | Yantian |
Export Percentage | 41% - 50% |
No.of Employees in Trade Department | 3-5 People |
Language Spoken: | English, Chinese, Spanish, Japanese, Portuguese, German, French, Russian, Korean, Italian |
b) Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Switch Power Supply 12V 15 Watt for LEDs
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 10 Pieces pc
- Supply Capability:
- 10,000 Pieces per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches