seam submerged arc welded pipe flat head chamfering machine
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Spiral welded pipe/straight seam submerged arc welded pipe flat head chamfering machine
Spiral welded pipe/straightseam submerged arc welded pipe flat head chamfering machine mainly is used tocrew cut the pipe end of spiral welded pipe or straight seamsubmerged arcwelded pipe and finish the edges. The finished edges are homogeneous andbeautiful.
Specifications
1.The pipe make as customerized
2.used in the water pipe,gas,oil pipe
3.machine meet API-5L,GB9711.2 Standards
Spiral welded pipe flat head chamfering machine process:Loading pipe – connecting pipe – pinching – flat head chamfering – loosening the clamp – exiting the pipe
Spiral welded pipe flat head chamfering machine mainly is used to crew cut the pipe end of spiral welded pipe and finish the edges. The finished edges are homogeneous and beautiful.
The bearing type of spiral welded pipe flat head chamfering machine.
No
| Model
| Specification(mm)
| Length(m)
| Capacity(Kw)
| Area(M2) |
1 | ST-400 | Φ219~Φ426 | 6~12 | 70 | 5×23 |
2 | ST-650 | Φ219~Φ630
| 6~12 | 80 | 5×23 |
3 | ST-800 | Φ325~Φ820
| 6~12 | 60 | 5×23 |
4 | ST-1000 | Φ426~Φ1020
| 8~12 | 70 | 5×23 |
5 | ST-1400 | Φ508~Φ1420
| 8~12 | 90 | 5×23 |
6 | ST-1800 | Φ630~Φ1820
| 8~12 | 100 | 5×23 |
7 | ST-2400 | Φ720~Φ2400
| 8~12 | 150 | 5×23 |
8 | ST-3000 | Φ820~Φ3000
| 8~12 | 160 | 5×23 |
9 | ST-3500 | Φ1020~Φ3500
| 8~12 | 180 | 5×25 |
- Q: A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Yes, the width of the bearing plate can be a deviation from the length.
- Q: What is rolling forming processing?
- A special rolling tool is used to exert certain pressure on the surface of the workpiece so as to make the surface metal flow.
- Q: Improvement in rolling forming process
- It is difficult to control the rolling process and can cause waste easily.
- Q: Introduction of roll forming process
- With the progress of technology and the development of production, more and more attention has been paid to the roll forming process.
- Q: What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Generally speaking, to consider the use of rollers in the requirements, including: 1., good wear resistance, 2. toughness, 3., high hardness, 4. hardened layer (easy to wear after repeated repair)
- Q: What is the surface rolling forming machine process?
- The rolling process using metal at room temperature, cold plastic characteristic, through the rolling tool is the rolling tool to put some pressure on the metal surface, so that the workpiece surface by plastic deformation, the height to the lower tissue slip, the surface roughness decreased.
- Q: Process mould for rolling forming process
- Rolling forming is more complicated and requires higher than rolling thread. The die design is based on the different shapes of the workpiece, the design of the rolling plate into a cross section or a few sections, can use synchronous type; also can use grading type.
- Q: Material and equipment for roll forming process
- Rolling process is a cold forging process, which can be used for rolling and forming a lot of materials. Among them, low carbon steel is a material commonly used in rolling forming, and non-ferrous metal is more suitable for roll forming.
Send your message to us
seam submerged arc welded pipe flat head chamfering machine
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
