Ratchet Cable Cutter 2 Hot Sale and High Quality

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

1.Two stage pumping action for rapid ram advance to the connector hold position with minimum pumping action.

1.Design to accommodate hexagonal dies for applying compression fittings to copper,aluminum conductors.

2.180° rotatable head.

3.The glass fiber operation insulates the stick, can bear the electric voltage 200KV,keeping on the minute.

4.The pressure outside the body adjusts to press the valve, don't need the whole structure to lie down.

5.Accessories:

Crimping dies:50,70,95,120,150,185,240,300,400mm²

6.Crimping force:13T

7.Crimping range:Cu 50-400mm²

8.Stroke: 38mm

9.Oil capacity: 200cc

10.weight:approx.7.80kg

ratchet cable cutter
Cutting range of three models:
1.dia.max.32mm
2.dia.max.75mm
3.dia.max.100mm

Ratchet cable cutter

Application:It is used for cutting copper&aluminum conductor and cable.

Parameter:

Model	Cutting Range	Weight(Kg)
XLJ-1	≤ ¢32 Copper&Aluminum conductor	0.98
J-75	≤ ¢75 cable (Copper&Aluminum conductor)	4
J-100	≤ ¢100 cable (Copper&Aluminum conductor)	6

Q: TOHNICHI torque wrench, where to introduce the use of it?: Tighten the nut and adjust the torque (then stop immediately when the torque is reached). Please note that all the consequences of violating the normal procedures (especially the removal of parts or the use of excessive force) are the sole concern of the parties.

Q: Working principle of hydraulic pulse wrench: An oil hydraulic wrench, as the name suggests, is an impact wrench that uses hydraulic oil to drive a blow shaft to produce torque.

Q: How can the heat treatment process be formulated?: Because the hardenability of 45 steel is low, the 10% brine solution should be used at a high cooling rate. The workpiece into the water, should be hardened, but not cold, if the workpiece in the brine cold, it is possible to make the workpiece cracking, this is because when the workpiece is cooled to about 180 DEG C when austenite transforms into martensite rapidly caused by excessive stress caused by. Therefore, when the quenched workpiece is cold to the temperature zone, a slow cooling method should be adopted. As the water temperature is difficult to grasp, we must rely on experience to operate, when the workpiece shaking in the water stopped, you can water out of air cold (such as oil, cold better). In addition, the workpiece into the water should be moving, not static, should be in accordance with the geometry of the workpiece, regular movement. The stationary cooling medium plus the stationary workpiece causes uneven hardness and uneven stress, causing the workpiece to become deformed and even crack.45 pieces of quenched and tempered steel after quenching hardness should reach HRC56~59, the possibility of large section low, but not less than HRC48, otherwise, the work has not been fully quenched sorbite, appear even ferrite may in the organization, the organization through tempering, is still retained in the base body, not up to quality objective.

Q: Is the ratchet wrench fast?: The front of the ratchet wrench is driven, mainly with the sleeve.

Q: How to distinguish movable spanner and adjustable spanner?: Different name only, layman called "active wrench", the expert is called "adjustable wrench"

Q: What's the difference between manual, pneumatic, and torque wrenches?: Pneumatic torque wrench torque can be adjusted, and the pneumatic wrench can not generally pneumatic torque wrench, pneumatic wrench, precision can reach 5%, and the regulation range of torque can reach 12000 nm.

Q: The difference between brush and brush in rechargeable electric wrench: However, because of the brushless electric wrench for low cost, small volume, light weight, the use of electric bicycle, so that there are two major technical problems, a small torque, there will be two low speed vibration, some electric bicycle manufacturers to the actual use of brushless electric wrench. With the development of modern science and technology at present. It is reported that, the technology leader in the electric bicycle industry in the electric wrench factory has successfully solved these two problems, so that the torque brushless motor with a brush pressing type motor, low vibration has been controlled in the range of the general feel. The motor will naturally become the ideal and high efficiency high torque, low noise, long continuous force to the target, the brushless electric wrench will become the main electric wrench for electric bikes in the next few years.

Q: How much do you charge for a general wrench?: You are talking about a movable wrench, also called a live wrench, and the opening size can be adjusted with a knob

Q: What's the inside of the six socket spanner for?: But in fact, there is often a space limit, the wrench can not keep a straight line with the six corners of the screw, this time, the six angle ball head can be put into use!

Q: How can the electric drill chuck be removed?: With a suitable size of the pipe, just hold the drill clamp coat, the middle part of the hammer and the shell separation, inside of the thread is two disc, three catch rearranged into thread, plus fixed coat.

Send your message to us

*Email

*TEL

*Quantity

*Unit