Multifunctiona l crimping pliers HAND TOOLS 301
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
Specification
Light stripping:
Comfortable handle
Whole heat treatment:
Precision grinding
MODEL:301
SPEC:8"
QUANTITY PER CARTON(PCS):12/72
G.W./N.W.(KG):19/18
PACK.DIEM(CM):33*29*27.5
WIRE STRIPPER
Key specification:
1.cut any cleanly strips electrical wire from 10 to 22 gauge
Insert tip of wire into marked holes to determine the size of the wire to be stripped
Squeeze the handle to strip easily and without nicking the wire
2.crimps both insulated and non-insulated ignition terminals
3.tool has black oxide finish for rust resistance
4.Vinyl clad cushion grip handles insulate as well as provide comfort of use
Using the method of the wire stripping pliers
All by hand if the wire stripping pliers groove is then a simple select wire size cut a pull on the line. If and oblique mouth clamp like it by hand, clip to a certain strength, a pull on the line.
Key points:
according to the diameter of the wire, the wire stripper blade aperture
1.According to the thickness of the cable type, select the corresponding stripping knife
2.The cable will be ready in the middle stripping tool blade, to choose a good length of wire stripping
3.Hold the stripping tool handle, cable clip, cable force slowly slowly peeling off the outer skin
4.Loosen the tool handle, then remove the cable, cable metal neatly exposed outside, the rest of the plastic insulation intact.
- Q: How can I get a crystal head without a cable clamp?
- If there is a scrap of wire that has been made of crystal head, you can consider cutting the crystal head and leaving a small network cable that corresponds to the new cable. It might be better to handle it as an emergency. Can refer to the figure in the logo, connecting the first, second, third and 6 lines can be, if it is a standard T568B line sequence, namely orange and white, orange, green and white, green 4.
- Q: How do you measure current with a pliers universal watch?
- 1 before measuring, should first check whether intact core rubber insulated clamp. The jaw should be clean and free of rust, and there is no obvious gap after closure.2 when measuring, the current should be measured and the proper range should be chosen. If you can't estimate, you can select a larger number of courses, then reduce the number of files to the appropriate gear. When converting the range gear, it must be done in the case of no electricity or under the opening of the jaw so as not to damage the meter.3 measurement, the measured wire should be placed in the middle of the jaw with jaw, face such as noise, should be re opening and closing time, still have the noise, should handle the joint surface, in order to make accurate readings. In addition, not at the same time around the two wires.4 measurement of the electric current is less than 5A, to get more accurate readings, when conditions permit, the wire around a few more laps, into the jaw measurement, the actual current value should be put into the meter reading divided by the number of jaw root wire.
- Q: What's the difference between the brake caliper and the brake disc? What's the usage?
- At present, the structure of brake massage pairs is different, which can be divided into three types: drum type, disc type and belt type
- Q: Elevator safety rod pull rod action principle?
- The safety tongs are only useful for falling down, and the overspeed will only operate the speed limiter switch. Down speeding will first action speed limiter switch, the safety circuit of the elevator outage when the car stop, but also because of inertia continue to glide down, pull the card machinery overspeed governor rope which makes the safeties. For overspeed protection, the rope clamp is used and the speed limiter switch circuit is used.
- Q: Does the speed limiter of the elevator protect the elevator from speeding up?
- The utility model relates to a speed overspeed protection device for a heavy car, and adopts an ordinary speed limiter safety clamp structure, that is, a speed limiter safety clamp system is added to the heavy side.This type is a relatively intuitive way to prevent the car from speeding up to the top of the car by preventing heavy, downlink and overspeed. Due to the addition of a speed limiter safety clamp system to the heavy side, the layout of the hoistway is complicated as the structure of the heavy truck is changed greatly, and the whole elevator system is equipped with two sets of speed limiter safety tongs system. The use of the heavy duty safety tongs makes it impossible to use the hollow rail for the heavy side rails. Therefore, the overspeed protection of the car in this way is of high cost. But this configuration advantage is easy to match parts do not need to develop new products, components, especially for the kind of "on someone can reach under heavy space" and not "will be installed on the counterweight buffer has been extended to solid ground solid pile pier on the elevator, must be installed on the heavy safety clamp, this can put the ascending car overspeed protection device and the safety clamp to be made one reduce the extra cost.
- Q: Survey work should pay attention to what use clamp meter?
- Measurement of low voltage fuse device and the level of arrangement of low-voltage busbar current when the measurement should be protected by insulation isolation of each phase protector and a bus, in order to avoid white shorts, also should pay attention to not touch other live parts.
- Q: How do you cut the wire with pliers?
- Put the wire on the inside edge of the pliers, and the clamp is broken
- Q: How to measure the AC voltage with digital clamp meter
- General test and pass function, but the main function is to measure the current, there are exchanges, but also AC and DC dual-use.
- Q: Note the clamp meter
- Clamp meter is clamped in the wire, cut off the circuit state, current detection convenient testing instrument (also known as nondestructive measurement).Analog pointer multimeter and digital multimeter is current detection circuit is cut off, and the clamp meter just caught in the electric wire sheath, current can be detected. The operation is simple, do not need to test large current circuit can be directly connected to safety.Clamp meter, multimeter and insulation resistance meter are analogue and digital two.Standard range of detection: AC, DC are in the 2A to 200A or 400A or so, there are products that can detect 2000A high current;Another can detect the number of mA small current leakage detection products, and can detect transformer power, switching power supply sine wave other than the true value of sine wave (True, RMS) products. 1: detection objectAccording to different detection objects, alternating current, DC current, or leakage current, to choose the type of aircraft;
- Q: What are the cutting pliers used in orthodontics to cut out any type of silk?
- However, you ask the "filament cutter" actually should be called the ligature cutter, not cut off the main arch wire, main arch wire in the "filament" than ligature thick, may damage the "filament cutter" caused by "cutting edge" appear sharp groove wear.
Send your message to us
Multifunctiona l crimping pliers HAND TOOLS 301
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
